Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Restoring a 39-7
#16

I prefer to keep rubber and wires separate. Icon_lol
#17

Thanks, I'll see if my local electronics shop has any...

Edit:

No luck. I have to go to the Internet. Any decent sources for these? I cannot locate any 6000pF caps, only 4700pF.

So what can I do? 4700 is enough, 10000 too much, or should I wire 3 2200's in parallel (I'd rather not tempt the fates of MTBF this way)?

Also there is one other silver mica capacitor in there - it's part 6A on the schematic. The problem is it's listed as a 20mfd device and there's no way this is 20mfd, it's just way too small. Elsewhere on the schematic it's listed as 20mmfd, which makes a lot more sense for this type of capacitor.
#18

It sings again!

After putting up with the repaired speaker that tended to muddle the sound and distort at medium-high volumes, I decided to take a closer look

The speaker was slowly disintegrating - small cracks were developing, and the most careful light touch caused the cone to split.

So I had the speaker reconed.

It's now a whole different radio. Plays loud, tight, and clear at all volumes.

I probably put more money I to this than I should, but it would have been a pity to leave it in such poor condition.

   
#19

Speaker looks very nice. Who did you send it to for reconing?
#20

The Speaker Shop:

http://thespeakershop.com
#21

Nice set! You've got the delux model with the brass escutcheon around the dial. Many years ago I had the chairside version of that set. Wish I hadn't sold it! Good player and very sensitive too.
Terry
#22

Actually, this one doesn't. It's pretty plain. I have a nearly identical model with the preset tuning buttons and the brass escutcheon though. You are right about the play quality and sensitivity though. A solid little radio. The guy who had it before me wrote 38-12 on the chassis, but it is a 39-6 as far as I can tell.

Edit: no, it isn't, it *is* a 38-12 chassis. Just double-checked the schematic. Someone put a dial from a 39-6 on it and stuck it in a 39-6 cabinet. >:-(

Aw crap! Just noticed I posted about the the speaker in my 39-7 thread. At least the 39-7 is a real one.




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco Model 38-7: what caps & resistors do fail typically?
Since you stated earlier, you have a console 38-7XX.  They also had a 38-7T (table), and 38-7CS (chairside).  A very nic...GarySP — 01:18 PM
Part numbers to model cross
That I wouldn't know, but sometimes the radio document itself shows one, same as the capacitor cans' etc pinouts.morzh — 12:46 PM
Part numbers to model cross
Thank you morzh, that is exactly what I was looking for. Now , is there some where that shows pinouts for Philco power ...Jim Dutridge — 11:37 AM
Restoration of the Canadian General Electric A-87
Thanks for your help Michael. In fact, this video is only an intermediate result. Later I had to apply another tinting l...RadioSvit — 09:01 AM
Restoration of the Canadian General Electric A-87
Great job on the cabinet. PS. In the US notation, "kenotron" refers to specific type of tubes; we call re...morzh — 08:24 AM
Part numbers to model cross
This document has at least some tables of models and parts used. Example: Choke 32-7572, used in 604 radio. Search f...morzh — 08:19 AM
Restoration of the Canadian General Electric A-87
I also checked all the radio tubes on my Hickok 530 tube tester. The 5Z3 kenotron turned out to be faulty, all the other...RadioSvit — 08:02 AM
Restoration of the Canadian General Electric A-87
Well... While the varnish is drying up, I started repairing the chassis... Of course I started by replacing the pa...RadioSvit — 07:12 AM
Philco Model 38-7: what caps & resistors do fail typically?
Hello Martin, Welcome aboard our little community what great Model 38-7 Sincerely Richardradiorich — 12:30 AM
Philco Model 38-7: what caps & resistors do fail typically?
Welcome to the Phorum Martin. I count about 9 paper caps, the 3 electrolytic caps and 2-Y2 safety caps to replace th...RodB — 09:44 PM

[-]
Who's Online
There are currently no members online.

>