Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Mershon Condenser
#1

Hello all,

I have a radio (Emerson Model F) from 1929 that
has a three section Mershon Condenser as the filter
caps (8 uF each).

I have removed it from the chassis and at least for
now have replaced it with modern 10 uF caps. The
radio is working fine.

I am wondering if this cap has any collector value?
I did not see any listed on eBay at all but I have
heard that they are sought after by collectors etc...

It would need to be gutted and re-stuffed of course,
it is very corroded along the top copper rim.

Anyone know anything about these caps?

Thanks,

Herb, KA2ZOH
Ithaca NY
#2

I have rebuilt several. They are not as easy as the single cap Mershons found in some Philcos.

"I just might turn into smoke, but I feel fine"
http://www.russoldradios.com/
#3

Chassis with Mershons caps are not that rare. I recently girt one from Kutztown that was pretty much junked.
You can rebuild them as usual aluminum can caps.
There are articles, some of them here from people who rebuilt them.
They are of course eye candies when cleaned and polished. Some folks install them in chassis that never had any aluminum cans or have them in totally different place, just to put them in for looks.
#4

OK, thanks for the responses. I think I'll hang onto this one
and someday try to clean it up and re-install it in
the radio.

Low priority at this point!

Herb S.




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco model 38 code 121 not receiving signal.
So one last question before I finish this radio. Regarding the speaker and output transformer. I salvaged the original o...Stormlord5500 — 09:31 AM
462ron
It’s on the bottom of the homepage of our Philcoradio.com homepage! Ron462ron — 07:20 AM
Model 70 Cabinet Trim
Steve might have some trim left. Not sure he is making anything.morzh — 06:12 AM
Model 70 Cabinet Trim
Hello musar, First all welcome to the forum and yes that is true that steve stopped making trim . Sincerely Richar...radiorich — 12:13 AM
Model 70 Cabinet Trim
I have recently come into possession of a Model 70.  The trim around the base needs to be replaced.  If this were years ...musar — 12:07 AM
philcorepairbench.com - shadow-meter
Anyone know of a way to recover these files from the repair bench? Thanks. fenbach — 11:16 PM
Philco model 38 code 121 not receiving signal.
That's true. Of course If I were to get a vtvm I'd probably have to sink money in to it to get it working right. Probabl...Stormlord5500 — 08:44 PM
Philco model 38 code 121 not receiving signal.
A DMM is good enough. One rarely has to measure indictance, but if you do, short of getting a serious LCR meter (I hav...morzh — 07:35 PM
Testing a speaker and output transformer Trutone A2-G
You guy's are right on. I found a broken wire on the speaker plug that I replaced and all is well now. Have better volu...murf — 03:43 PM
Philco model 38 code 121 not receiving signal.
I need to get a vtvm. I think that little component tester is just more accurate. Plus it shows the inductance which is ...Stormlord5500 — 03:07 PM

[-]
Who's Online
There are currently 1486 online users. [Complete List]
» 2 Member(s) | 1484 Guest(s)
AvatarAvatar

>