Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

The "cheap" Philcos of the Depression
#1

We all know Philco built several low priced radios during the early Depression years. I have three - the 80B, 57C, and 84B. Though they only have four tubes, I have to say these three radios have been three of the more painful restorations I've ever done. From my experience, good alignment of these is next to impossible. Plus, my 57C and 80B still have intermittent problems, even though I've gone through them with a fine-tooth comb.

Though they aren't the greatest performers around, they do usually seem to be able to bring in local stations well. I guess they served their purpose - to be an inexpensive way to own a radio in the 1932-34 time frame, when the Depression was having its worst effects on people. To me, that makes these radios an important part of history.

Anyone have any better luck with these lower end table models?

Tom
#2

I've worked on a lot of 80 and 84 sets; the only thing I've ever done to a 57 was to change a power transformer in one that had otherwise been recapped.

The 84s always seem to outperform the 80s, in my experience. On a decent longwire, I can get a fair amount of distance as well as locals on an 84. On most 80s, I do well to get the locals.

The one 57 I did the transformer transplant on performed really well, like an 84.

It has been my experience that in order to get the most performance out of these sets, that one needs to replace all carbon resistors as well as all paper and electrolytic capacitors. The resistors in these are often way out of tolerance.

As these use an autodyne mixer-oscillator circuit similar to Model 89, baking the oscillator coil forms and rewinding them is also something that should be done for optimal performance.

--
Ron Ramirez
Ferdinand IN
#3

As it happens, a fellow had sent me three radios to refurbish: two Model 84s and an 80.

In redoing this Model 80, I have come up with a quick and cheap way to somewhat increase the sensitivity of the 80. I'll put it together and post it in the Philco Electronic Restoration section later.

--
Ron Ramirez
Ferdinand IN
#4

Sounds good Ron! It seems like my 80 only picks up local stations and that's only when it was in the mood!

Tom
#5

EDIT: Details of these performance mods may now be viewed here:
http://www.philcorepairbench.com/tips/svctip43.htm
http://www.philcorepairbench.com/tips/svctip44.htm

--
Ron Ramirez
Ferdinand IN




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM
Philco model 38 code 121 not receiving signal.
Well why not! :lol:Stormlord5500 — 03:14 PM
Philco model 38 code 121 not receiving signal.
Good luck next thing you know you will be winding coils just for the fun of it. DavidDavid — 11:29 AM
Testing a speaker and output transformer Trutone A2-G
morzh Short-circuited turns can be considered as a half-dead transformer. But on this case transformer will hot and s...Vlad95 — 11:01 AM
Testing a speaker and output transformer Trutone A2-G
I am not sure how a transformer could be weak. It could be inadequate, but only when you replace the original with somet...morzh — 09:56 AM

[-]
Who's Online
There are currently 2239 online users. [Complete List]
» 5 Member(s) | 2234 Guest(s)
AvatarAvatarAvatarAvatar
Avatar

>