Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

philco 84 Ecap lead placement
#1

I am re-stuffing the can in my 84 and I am lost on where to put the leads. I replace an 8uf and a 4uf but I dont know what wires connect to them.

Do the 2 positives get twisted together and go to the rectifier?

Or do the 2 grounds get twisted?

Not sure of the schematic since I cant read them well.
Schematics here:
http://www.nostalgiaair.org/PagesByModel...013875.pdf

Any help on this is appreciated
Kirk

Times I have been electrocuted in 2021
As of 1/01/2021
AC: 4 DC: 1
Last year: 6
#2

Kirk,

The top-side leads definitely do NOT get tied together. The 8 uF goes to the rectifier. The 4 uf goes to the top side side of cap 32.

The negative leads are electrically connected. Don't know if they need to be twisted together or not, whichever is easier. These leads go to the center tap of the power transformer and to Cap 28 and resistor 30.

Good luck.
Jon
#3

The pos go to your speaker (thats where all leads tie together on my 84)look at the sch at the x connections at white and green/white. When there is a dot on the sch that means that the wires are connected.
#4

DONE!
I have a working radio with complete recapping and no off value resistors!


THanks guys Icon_mrgreenIcon_mrgreen

Times I have been electrocuted in 2021
As of 1/01/2021
AC: 4 DC: 1
Last year: 6




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco model 38 code 121 not receiving signal.
So one last question before I finish this radio. Regarding the speaker and output transformer. I salvaged the original o...Stormlord5500 — 09:31 AM
462ron
It’s on the bottom of the homepage of our Philcoradio.com homepage! Ron462ron — 07:20 AM
Model 70 Cabinet Trim
Steve might have some trim left. Not sure he is making anything.morzh — 06:12 AM
Model 70 Cabinet Trim
Hello musar, First all welcome to the forum and yes that is true that steve stopped making trim . Sincerely Richar...radiorich — 12:13 AM
Model 70 Cabinet Trim
I have recently come into possession of a Model 70.  The trim around the base needs to be replaced.  If this were years ...musar — 12:07 AM
philcorepairbench.com - shadow-meter
Anyone know of a way to recover these files from the repair bench? Thanks. fenbach — 11:16 PM
Philco model 38 code 121 not receiving signal.
That's true. Of course If I were to get a vtvm I'd probably have to sink money in to it to get it working right. Probabl...Stormlord5500 — 08:44 PM
Philco model 38 code 121 not receiving signal.
A DMM is good enough. One rarely has to measure indictance, but if you do, short of getting a serious LCR meter (I hav...morzh — 07:35 PM
Testing a speaker and output transformer Trutone A2-G
You guy's are right on. I found a broken wire on the speaker plug that I replaced and all is well now. Have better volu...murf — 03:43 PM
Philco model 38 code 121 not receiving signal.
I need to get a vtvm. I think that little component tester is just more accurate. Plus it shows the inductance which is ...Stormlord5500 — 03:07 PM

[-]
Who's Online
There are currently 2006 online users. [Complete List]
» 2 Member(s) | 2004 Guest(s)
AvatarAvatar

>