Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco 46-1209 Push button alingment
#1

I noticed that when I align the push buttons on the 46-1209, the signals are not as strong as when tuning the same station using the dial tuning.

Is this normal?

Thanks,
Wayne
#2

I am not familiar with the 46-1209, but it is common that antique radio push buttons are not always the most accurate way to tune in a station. Many of the mechanisms were a little sloppy, and age doesn't help.

The artist formerly known as Puhpow! 8)
#3

Something interesting is that the presets don't all have the same frequency range. The leftmost are meant for lower-band AM while the rightmost are meant to higher-band AM.

Technically you bypass part of the main tuning circuitery in favor of a set of secondary tuner circuits. Perhaps it has to do with your recap?

On my 47-1230 the stations that I get do tune in quite strong, but I am having the hardest time to find any stations. There isn't much AM reception anyway, everyone broadcast in FM.

Similarly to your problem, my FM tuner isn't as strong as my AM tuner... Icon_sad

-Mars
#4

Marsupial, interesting... I seem to get better reception on FM than on AM on my 47-1230. I dont get all the AM stations that other am radios get but the FM seems very good.
#5

Warren, I get better reception on FM, but not as loud. I know it has to do with some still un-recapped capacitors. I have not touched most of that stage yet.

-Mars
#6

With my 47-1230 I have good strong output on manual tuned AM and SW as soon as I turn radio on. The manually tuned FM tends to drift off station until radio has warmed up for about 10-15 minutes, then it stays stable, but at much lower volume than AM. Presets are louder than manual tuning. I receive all available stations, up and down the dial, on all three bands manually. As for my 40-180 and 39-35, All of my station presets sound much louder than manual tuning, I think because they can be individually fine tuned to almost perfect reception. Just wish the 47-1230 had a button or two for FM preset! Now my Zenith 8-S-563, the volume is the same whether tuned manually or with the push buttons.
#7

I too would like FM presets.

There is barely anything in AM nowadays here, but FM has lots of good strong stations. They even stopped broadcasting news reports, traffic reports and sports (hockey) on AM. Icon_sad all on FM talk radio now.

I really need just one FM preset.

-Mars




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco Model 38-7: what caps & resistors do fail typically?
Since you stated earlier, you have a console 38-7XX.  They also had a 38-7T (table), and 38-7CS (chairside).  A very nic...GarySP — 01:18 PM
Part numbers to model cross
That I wouldn't know, but sometimes the radio document itself shows one, same as the capacitor cans' etc pinouts.morzh — 12:46 PM
Part numbers to model cross
Thank you morzh, that is exactly what I was looking for. Now , is there some where that shows pinouts for Philco power ...Jim Dutridge — 11:37 AM
Restoration of the Canadian General Electric A-87
Thanks for your help Michael. In fact, this video is only an intermediate result. Later I had to apply another tinting l...RadioSvit — 09:01 AM
Restoration of the Canadian General Electric A-87
Great job on the cabinet. PS. In the US notation, "kenotron" refers to specific type of tubes; we call re...morzh — 08:24 AM
Part numbers to model cross
This document has at least some tables of models and parts used. Example: Choke 32-7572, used in 604 radio. Search f...morzh — 08:19 AM
Restoration of the Canadian General Electric A-87
I also checked all the radio tubes on my Hickok 530 tube tester. The 5Z3 kenotron turned out to be faulty, all the other...RadioSvit — 08:02 AM
Restoration of the Canadian General Electric A-87
Well... While the varnish is drying up, I started repairing the chassis... Of course I started by replacing the pa...RadioSvit — 07:12 AM
Philco Model 38-7: what caps & resistors do fail typically?
Hello Martin, Welcome aboard our little community what great Model 38-7 Sincerely Richardradiorich — 12:30 AM
Philco Model 38-7: what caps & resistors do fail typically?
Welcome to the Phorum Martin. I count about 9 paper caps, the 3 electrolytic caps and 2-Y2 safety caps to replace th...RodB — 09:44 PM

[-]
Who's Online
There are currently 1154 online users. [Complete List]
» 2 Member(s) | 1152 Guest(s)
AvatarAvatar

>