Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Help with proper verbage of a part...
#1

The plastic piece that the electric cord passes through and protects it from the chassis...and does Radio Shack have those?
#2

Could be a grommet or a clamp if it actually holds the wire too. Radio shack used to carry them but not sure if they do anymore. Worth a try I spose.
#3

Except Radio Shack stores are no longer brick and mortar, or almost so. Online possibly, but these things are not hobbyist exclsively and could be sold in hardware stores, or in Lowes/Home Depot.
#4

Also sold by Mouser.
#5

As far as a term for it I think it may be called a 'line restraint'. I don't know if any suppliers call it that Icon_smile Also "Heyco Bushing" relating to a major manufacturer of them.
#6

Thanks all! That helped!
#7

"Strain relief" is another term that's used.
Keith
#8

Grommet
#9

Lowes has them in drawers in the hardware section, they sell grommets too.
#10

Radio Daze sells those strain relief pieces also.
#11

Well the old timers often called an unidentified part a framis. Plural is framae. Indeed the crimp imposed by these little things caused many a cord to fail, but not that many fires. So they used 'em and still do with very few lawsuits.




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
PT 6 chassis screws size???
Hello bridKarl, that sounds right or maybe 8/32 . Sincerely Richardradiorich — 01:00 AM
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM
Philco model 38 code 121 not receiving signal.
Well here it is. It ain't pretty, but hopefully it'll work. I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM

[-]
Who's Online
There are currently no members online.

>