Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

42-1012 question
#1

Morning folks.
I just cleaned up a 42-1012 and the cabinet looks great. I am in the need for a source on the faceplate, buttons and knobs. Being new to this game I don't have much of an idea where to start looking and any help would be grand.
Thanks in advance.
Shepard
#2

Hi

A good source for the buttons and knobs is Old-Time Replications.

http://www.antiqueradioknobs.com/

As for the escutcheon, I'm afraid you are out of luck. No one reproduces that escutcheon, and it is highly unlikely that anyone ever will. It simply isn't in enough demand for anyone to justify reproducing it.

--
Ron Ramirez
Ferdinand IN
#3

Thanks Ron for your help on the knobs and buttons. Any idea where I might be able to purchase a faceplate?
Shep
#4

Sorry, no...your only hope is a junk set at this point, or find someone who has junked a 1942 Philco console with a 10-pushbutton escutcheon. And even that will probably be warped, thanks to the lousy Tenite plastic Philco used in 1941-42.

--
Ron Ramirez
Ferdinand IN




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
PT 6 chassis screws size???
Hello bridKarl, that sounds right or maybe 8/32 . Sincerely Richardradiorich — 01:00 AM
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM
Philco model 38 code 121 not receiving signal.
Well here it is. It ain't pretty, but hopefully it'll work. I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM

[-]
Who's Online
There are currently 654 online users. [Complete List]
» 1 Member(s) | 653 Guest(s)
Avatar

>