Posts: 375
Threads: 79
Joined: Oct 2014
City: Winter Haven, FL
I just started rebuilding a Silvertone 101.614 chassis. The triple capacitor metal can is missing, and I know I can just replace it with three individual caps, but the three dial lamps are missing also. Does anyone know what type bulbs these are? The schematic is really hard to read. It looks like it says type 66, but I cannot find any reference to a type 66 bulb. It will be a while before I can actually power it up, so I just wanted to replace the lamps first.
Thanks in advance.
Pat
Posts: 1,562
Threads: 56
Joined: Nov 2008
City: Sedona, AZ/Placentia/CA
Pat, it really helps to post a picture of the radio or at least a link to the schematic so we can help.
Jerry
A friend in need is a pest! Bill Slee ca 1970.
Posts: 205
Threads: 6
Joined: Jun 2006
City: Moundsville
State, Province, Country: WV
Pat,
After looking at a magnified schematic, I believe the dial lamp is a #44.
Carl
Northern Panhandle, WV
Posts: 375
Threads: 79
Joined: Oct 2014
City: Winter Haven, FL
(10-17-2014, 06:54 PM)jerryhawthorne Wrote: Pat, it really helps to post a picture of the radio or at least a link to the schematic so we can help.
Jerry
Sorry Jerry,
Here's the only schematic I could find.
Posts: 375
Threads: 79
Joined: Oct 2014
City: Winter Haven, FL
(10-17-2014, 07:24 PM)Carl Travis Wrote: Pat,
After looking at a magnified schematic, I believe the dial lamp is a #44.
Thanks Carl,
I'll go with that. But now, I've run into another problem, thanks to an unreadable schematic.
The schematic shows two line-to-ground caps, C45 and C46. However, the chassis has one across-the-line cap, .01 @ 600V. Can I replace that with an X2 safety cap, AND and two .01 Y2 caps as well? Or should I just remove the across-the-line cap and add two line-to-ground caps, as the schematic indicates?
Pat
Posts: 7,323
Threads: 270
Joined: Dec 2009
City: Roslyn Pa
If indeed it is a 44 bulb you may want to use a 47. It runs a bit cooler. Some sets have the bulb very close to plastics dial which can be problematic. You may have seen sets with brown or black marks on the dial. Those can be burn marks from the bulb.
The voltage for the bulb is usually connected in parallel off of the heater winding on the power transformer. Where you could run in to problem is if your set powered the bulb off of the AC line though a balist tube or the heaters strung in series. Your set doesn't. In this type of circuit the voltage and current are very important. Wrong bulb can burned out( usually very quickly), damage the balist tube or other tube in that heater circuit
GL
Terry
Posts: 375
Threads: 79
Joined: Oct 2014
City: Winter Haven, FL
(10-17-2014, 07:57 PM)Radioroslyn Wrote: If indeed it is a 44 bulb you may want to use a 47. It runs a bit cooler. Some sets have the bulb very close to plastics dial which can be problematic. You may have seen sets with brown or black marks on the dial. Those can be burn marks from the bulb.
The voltage for the bulb is usually connected in parallel off of the heater winding on the power transformer. Where you could run in to problem is if your set powered the bulb off of the AC line though a balist tube or the heaters strung in series. Your set doesn't. In this type of circuit the voltage and current are very important. Wrong bulb can burned out( usually very quickly), damage the balist tube or other tube in that heater circuit
GL
Terry Even though the schematic doesn't show it, I've got three lamps in series off of the heater windings. Still use #47?
Pat
Posts: 1,562
Threads: 56
Joined: Nov 2008
City: Sedona, AZ/Placentia/CA
Pat, I would follow the schematic and replace the line input with two .01mfd either "Y" or "XY" caps as indicated. Replace the existing one across the A/C line. These should be "safety caps" used in this position. They will not fail shorted which is nice across the A/C line. Many people just remove them totally. It won't hurt the radio but may increase the noise from A/C line problems.
Best, Jerry
A friend in need is a pest! Bill Slee ca 1970.
Posts: 375
Threads: 79
Joined: Oct 2014
City: Winter Haven, FL
(10-17-2014, 08:22 PM)jerryhawthorne Wrote: Pat, I would follow the schematic and replace the line input with two .01mfd either "Y" or "XY" caps as indicated. Replace the existing one across the A/C line. These should be "safety caps" used in this position. They will not fail shorted which is nice across the A/C line. Many people just remove them totally. It won't hurt the radio but may increase the noise from A/C line problems.
Best, Jerry
Thanks Jerry,
Just the answer I was looking for.
Pat
Posts: 7,323
Threads: 270
Joined: Dec 2009
City: Roslyn Pa
Hey Pat
Are you sure the bulbs are in series?? That would mean that each bulb would have to be rated @ 2v each.
Terry
Posts: 375
Threads: 79
Joined: Oct 2014
City: Winter Haven, FL
(10-18-2014, 08:33 AM)Radioroslyn Wrote: Hey Pat
Are you sure the bulbs are in series?? That would mean that each bulb would have to be rated @ 2v each.
Terry
My error, Terry.
Maybe I need to change my medication. They are in parallel.
Pat
Users browsing this thread: 1 Guest(s)
|
|
Recent Posts
|
|
Philco P45-6365 Universal Transformer Instruction Manual
|
| Can anyone guide me to where this may be found?GRG — 03:00 PM |
|
54C Complete Teardown/Rebuild
|
| I don't think that I have encountered a 12Z3 before, curious how it uses one of those but includes a #43, which is a 25 ...Arran — 02:17 PM |
|
HiFi (Chifi) tube amp build - but my own design.
|
| It's the other forum. I'm also in DIY, but mostly read there. Honestly, I kinda jumped into this without much thought to...TV MAN — 10:43 AM |
|
Philco 71 Code 125
|
| Hello,
I am in need of a schematic for this radio. Mine has the three separate circular tube shields and a shadow me...dconant — 08:06 AM |
|
Stromberg Carlson 1500 Squeal
|
| And life just keeps getting more complicated.dconant — 07:57 AM |
|
54C Complete Teardown/Rebuild
|
| Hello Roy,
here is this one
sincerely Richardradiorich — 12:45 AM |
|
54C Complete Teardown/Rebuild
|
| Richard,
Had grabbed it already but thank you just the same. I find myself wanting to find some way to block out the...glyphmon — 12:03 AM |
|
54C Complete Teardown/Rebuild
|
| Hello roy,
here is a link to the schematic .
Sincerely Richardradiorich — 11:54 PM |
|
54C Complete Teardown/Rebuild
|
| Richard,
The Silvertone 2014 also is a transformerless set, so I am incorporating a 1:1 600 ohm audio isolation transfo...glyphmon — 11:37 PM |
|
Preliminary work on wife's Silvertone 2014
|
| Did an alignment today which was interesting. IF alignment went great, almost all was already spot-on. Adjusting on th...glyphmon — 11:35 PM |
|
Who's Online
|
There are currently 1996 online users. [Complete List]
» 2 Member(s) | 1994 Guest(s)
|
|
|
|
 
|
![[-]](https://philcoradio.com/phorum/images/bootbb/collapse.png "[-]")
