Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco 38-116
#1

I LOVE my Philco 38-116 but recently its been giving me a real problem. The radio does not pick up on the AM band below 1300 on the dial and Shortwaave is spooty at best. I do not have a tube tester. Console was recaped and was working beautifully. Might have to replace some tubes. What do you think . I usually listed to this radio every nite!   Icon_sad
#2

This is not the first time this has happened to me on this set.
#3

Well, if you have spare tubes, you know what to do for the next 1/2 hour Icon_smile
#4

Had a similar problem on my 42-355, only to find a small dust bunny had made its home in part of the tuning capacitor. Once I took some compressed air and blew it out, the missing half of the dial returned. Can't say that it is something that simple causing the trouble on your 38-116. Of course my set has no back, which just invites dust inside. Not sure if your console has a back or not. Otherwise, yep, time to try different tubes.

Greg V.
West Bend, WI
Member WARCI.org
#5

My radio has no back also. Good point, It does collect a lot of dust. Will try that. Then its off to find some tubes if that does not work.
#6

I capped my 37-116 back in the '80s but didn't pull out the RF deck. After a year or so of working well it died. A small paper cap in the osc screen circuit shorted killed the LO. Pain to replace but fixed it and worked again.
Terry




Users browsing this thread:
[-]
Recent Posts
Philco Model 38-7: what caps & resistors do fail typically?
Since you stated earlier, you have a console 38-7XX.  They also had a 38-7T (table), and 38-7CS (chairside).  A very nic...GarySP — 01:18 PM
Part numbers to model cross
That I wouldn't know, but sometimes the radio document itself shows one, same as the capacitor cans' etc pinouts.morzh — 12:46 PM
Part numbers to model cross
Thank you morzh, that is exactly what I was looking for. Now , is there some where that shows pinouts for Philco power ...Jim Dutridge — 11:37 AM
Restoration of the Canadian General Electric A-87
Thanks for your help Michael. In fact, this video is only an intermediate result. Later I had to apply another tinting l...RadioSvit — 09:01 AM
Restoration of the Canadian General Electric A-87
Great job on the cabinet. PS. In the US notation, "kenotron" refers to specific type of tubes; we call re...morzh — 08:24 AM
Part numbers to model cross
This document has at least some tables of models and parts used. Example: Choke 32-7572, used in 604 radio. Search f...morzh — 08:19 AM
Restoration of the Canadian General Electric A-87
I also checked all the radio tubes on my Hickok 530 tube tester. The 5Z3 kenotron turned out to be faulty, all the other...RadioSvit — 08:02 AM
Restoration of the Canadian General Electric A-87
Well... While the varnish is drying up, I started repairing the chassis... Of course I started by replacing the pa...RadioSvit — 07:12 AM
Philco Model 38-7: what caps & resistors do fail typically?
Hello Martin, Welcome aboard our little community what great Model 38-7 Sincerely Richardradiorich — 12:30 AM
Philco Model 38-7: what caps & resistors do fail typically?
Welcome to the Phorum Martin. I count about 9 paper caps, the 3 electrolytic caps and 2-Y2 safety caps to replace th...RodB — 09:44 PM

[-]
Who's Online
There are currently 1437 online users. [Complete List]
» 1 Member(s) | 1436 Guest(s)
Avatar

>