Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco Model 112 Highboy
#1

I am looking at a Philco 112 Highboy. It's unrestored. The veneer is in good shape with a few scratches. It is one of the cabinets that Bel Geddes designed. Still has the label on the back of the cabinet. The owner is asking $195 which to me is high. What do you believe would be a fair price? I am out in the Portland OR area. Any feedback would be welcome. Thanks
#2

http://www.philcoradio.com/phorum/showth...p?tid=6087

One of the buys, $99, in 2013.

I say not above 130.

I bought a 111 a year and a half ago which shares the same chassis but is a highboy. $75.
#3

(02-14-2015, 10:32 PM)Umorzh Wrote:  http://www.philcoradio.com/phorum/showth...p?tid=6087

One of the buys, $99, in 2013.

I say not above 130.

I bought a 111 a year and a half ago which shares the same chassis but is a highboy. $75.

Thank you I appreciate the link and the feedback.
#4

Roy, too bad your not closer to AZ. I have a 112 restored I will be listing when I get back there. They are nice radios but I really don't want to worry about shipping them!
Jerry

A friend in need is a pest!  Bill Slee ca 1970.
#5

 I would say that $195 is way too much money for the majority of unrestored early 30's consoles. I say this because of where the market has gone not because I don't like them. Where I am, in which they are not nearly as common as the U.S midwest, anything over about $125 makes them a hard sell, and that's in good original condition. Almost all have just the single AM broadcast band, which ends at just over 1500 KC, it wasn't until 1932-33 that sets with a "police band" and shortwave became common. The other reason is because of the styling, even with the Norman Bel Geddes cabinets they are viewed as being old fashioned, and the dials and control panels are all sort of similar. It's a shame in one way in that they are not as appreciated, but then again that also makes them more affordable to those of us that like them.
Regards
Arran
#6

Difference is a questionable dinner for two and a few gallons of gas, so if you want a project take it.
#7

Unless stated otherwise, I found that all craigslist listings are negotiable.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM
Philco model 38 code 121 not receiving signal.
Well here it is. It ain't pretty, but hopefully it'll work. I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM
Philco model 38 code 121 not receiving signal.
Well why not! :lol:Stormlord5500 — 03:14 PM
Philco model 38 code 121 not receiving signal.
Good luck next thing you know you will be winding coils just for the fun of it. DavidDavid — 11:29 AM

[-]
Who's Online
There are currently 472 online users. [Complete List]
» 1 Member(s) | 471 Guest(s)
Avatar

>