Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

116b band swicth nob?
#1

     What Is the correct part for band switch? , round nob or a thumb lever  I have seen both , if it is the lever design what does it look like and was there felt washers behind the nobs?
#2

I'm not sure which goes on your set but there is a BS knob used only on some of the 1936 models. Here's a pic of it.
http://philcoradio.com/gallery/1936a.htm#y
That is what is on both of my 116X's. That was the best pic of that knob I found.
GL w/it
Terry
#3

I have also seen both the round black knob as well as the oddball bandswitch knob that was only used in the 1936 season (which Terry linked to above) on the early (shouldered) 116B, so I would say either one is OK.

--
Ron Ramirez
Ferdinand IN
#4

(03-27-2015, 09:20 PM)Ron Ramirez Wrote:  I have also seen both the round black knob as well as the oddball bandswitch knob that was only used in the 1936 season (which Terry linked to above) on the early (shouldered) 116B, so I would say either one is OK.

THANKS FOR QUICK REPLY Icon_crazy




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM
Philco model 38 code 121 not receiving signal.
Well here it is. It ain't pretty, but hopefully it'll work. I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM
Philco model 38 code 121 not receiving signal.
Well why not! :lol:Stormlord5500 — 03:14 PM
Philco model 38 code 121 not receiving signal.
Good luck next thing you know you will be winding coils just for the fun of it. DavidDavid — 11:29 AM

[-]
Who's Online
There are currently 527 online users. [Complete List]
» 2 Member(s) | 525 Guest(s)
AvatarAvatar

>