Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

1939 Silvertone 7252 Restore on Youtube
#1

Greetings Phorum:
I have a new series on YouTube if anyone is interested,
Link below

https://www.youtube.com/watch?v=KkGbm2GgC40
#2

Great!

Crist
#3

(09-26-2015, 12:49 PM)Crist Rigotti Wrote:  Great!

+1

John KK4ZLF
Lexington, KY
"illegitimis non carborundum"
#4

Hello Phorum:
Part 2 is now uploaded.
If interested link is below.
https://www.youtube.com/watch?v=EO_1ENuEl9s
#5

Hello Phorum:

Part 3 is now uploaded.
If interested link is below.


https://www.youtube.com/watch?v=Ruy-NJopP8c
#6

Link to part 3:

https://www.youtube.com/watch?v=Ruy-NJopP8c

Great job as always Buzz!

John KK4ZLF
Lexington, KY
"illegitimis non carborundum"
#7

Hello Phorum:

Part 4 is now uploaded.
If interested link is below.


https://www.youtube.com/watch?v=qG1M6g1LZFQ
#8

Sorry about the Stromberg, but I'm sure you'll get it straighten out one way or another.  Looking forward to see how the lacquer fill works out.

Is that little GE transistor made is the U.S. or Japan?

Thanks again, these are much better than Saturday cartoons!

John KK4ZLF
Lexington, KY
"illegitimis non carborundum"
#9

thanks....I'll be posting progress reports on the lacquer repair in future videos...Buzz
#10

(10-24-2015, 10:10 AM)Eliot Ness Wrote:  Sorry about the Stromberg, but I'm sure you'll get it straighten out one way or another.  Looking forward to see how the lacquer fill works out.

Is that little GE transistor made is the U.S. or Japan?

Thanks again, these are much better than Saturday cartoons!
As far as I can tell, it was made in USA
#11

Buzz, I watch your videos regularly and LOVED the little 1946 Bendix 0526A radio you featured in one of your recent cinematic efforts. So much so that I did mine up the same way! I hope in this case you go along with the adage that imitation is the sincerest form of flattery, because that three tone color combination hit a home run! Thanks for the inspiration. That little odd color under the tuning knob is glare from the overhead light in the room, not a paint defect.

   

Greg V.
West Bend, WI
Member WARCI.org
#12

(10-26-2015, 10:32 PM)NostalgiaRadioTime Wrote:  Buzz, I watch your videos regularly and LOVED the little 1946 Bendix 0526A radio you featured in one of your recent cinematic efforts. So much so that I did mine up the same way! I hope in this case you go along with the adage that imitation is the sincerest form of flattery, because that three tone color combination hit a home run! Thanks for the inspiration. That little odd color under the tuning knob is glare from the overhead light in the room, not a paint defect.

Wow..Looks great....good job....,,I love the looks on that Bendix model....Buzz
#13

You should go to Hollywood Buzz, I enjoy your productions, from the 110 prefix on the chassis label I am pretty sure that your Silvertone was made by Air King Products in Brooklyn, Air King used that Oatmeal box style antenna in a few models, and it works pretty good. The only AK's in my collection are Air Kings!

PAul

Tubetalk1
#14

(10-29-2015, 09:37 PM)Paul Philco322 Wrote:  You should go to Hollywood Buzz, I enjoy your productions, from the 110 prefix on the chassis label I am pretty sure that your Silvertone was made by Air King Products in Brooklyn, Air King used that Oatmeal box style antenna in a few models, and it works pretty good. The only AK's in my collection are Air Kings!

PAul

thanks paul
#15

Part 5 of my Silvertone series is now uploaded
Here is the link if interested.

https://www.youtube.com/watch?v=U7KNdPv664Y




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco Model 38-7: what caps & resistors do fail typically?
Since you stated earlier, you have a console 38-7XX.  They also had a 38-7T (table), and 38-7CS (chairside).  A very nic...GarySP — 01:18 PM
Part numbers to model cross
That I wouldn't know, but sometimes the radio document itself shows one, same as the capacitor cans' etc pinouts.morzh — 12:46 PM
Part numbers to model cross
Thank you morzh, that is exactly what I was looking for. Now , is there some where that shows pinouts for Philco power ...Jim Dutridge — 11:37 AM
Restoration of the Canadian General Electric A-87
Thanks for your help Michael. In fact, this video is only an intermediate result. Later I had to apply another tinting l...RadioSvit — 09:01 AM
Restoration of the Canadian General Electric A-87
Great job on the cabinet. PS. In the US notation, "kenotron" refers to specific type of tubes; we call re...morzh — 08:24 AM
Part numbers to model cross
This document has at least some tables of models and parts used. Example: Choke 32-7572, used in 604 radio. Search f...morzh — 08:19 AM
Restoration of the Canadian General Electric A-87
I also checked all the radio tubes on my Hickok 530 tube tester. The 5Z3 kenotron turned out to be faulty, all the other...RadioSvit — 08:02 AM
Restoration of the Canadian General Electric A-87
Well... While the varnish is drying up, I started repairing the chassis... Of course I started by replacing the pa...RadioSvit — 07:12 AM
Philco Model 38-7: what caps & resistors do fail typically?
Hello Martin, Welcome aboard our little community what great Model 38-7 Sincerely Richardradiorich — 12:30 AM
Philco Model 38-7: what caps & resistors do fail typically?
Welcome to the Phorum Martin. I count about 9 paper caps, the 3 electrolytic caps and 2-Y2 safety caps to replace th...RodB — 09:44 PM

[-]
Who's Online
There are currently 1234 online users. [Complete List]
» 2 Member(s) | 1232 Guest(s)
AvatarAvatar

>