Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Emerson 517 Moderne
#1

Well I had got 3 free radios a while back, one went to Terry, one is still in the box, this Emerson got done! The lighted dial pic is does not do justice, the cabinet came out OK, used Meguiars Wax and it came up good. I took the cabinet from a junker as the original had a big hole in top. 

It has been to the bench and it sounds quite nice, picks up my 250 Watt AM music station very well. So now I am wondering if I should give this to the guy who gave it to me, It was his Dad's.


https://www.flickr.com/photos/92577012@N...2698130911

What does ya think?

Paul

Tubetalk1
#2

Looks great!
Darn I thought you fixed the old cabinet!
Hear your going to be snow in pretty soon.
Got to get busy on that GE cabinet. I found
some small brads so I can nail the top back down.

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#3

By the time I fixed the hole It would have cost me way more than the junk set, I needed a knob and I took the case. I still have a chassis that is not too bad though it has the small tubes instead of the Octal like the one we fixed. 

Paul

Tubetalk1
#4

Nice!

What's that big white console The Emerson was sitting on for the pictures?  Icon_wink

I don't hold with furniture that talks.
#5

I would give it back, lots of memories of his dad. David
#6

(03-14-2018, 12:21 PM)EdHolland Wrote:  Nice!

What's that big white console The Emerson was sitting on for the pictures?  Icon_wink



That is my Whirlpool console sounds good especially if change was left in your pocket. Icon_lol

Paul

Tubetalk1




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco model 38 code 121 not receiving signal.
So one last question before I finish this radio. Regarding the speaker and output transformer. I salvaged the original o...Stormlord5500 — 09:31 AM
462ron
It’s on the bottom of the homepage of our Philcoradio.com homepage! Ron462ron — 07:20 AM
Model 70 Cabinet Trim
Steve might have some trim left. Not sure he is making anything.morzh — 06:12 AM
Model 70 Cabinet Trim
Hello musar, First all welcome to the forum and yes that is true that steve stopped making trim . Sincerely Richar...radiorich — 12:13 AM
Model 70 Cabinet Trim
I have recently come into possession of a Model 70.  The trim around the base needs to be replaced.  If this were years ...musar — 12:07 AM
philcorepairbench.com - shadow-meter
Anyone know of a way to recover these files from the repair bench? Thanks. fenbach — 11:16 PM
Philco model 38 code 121 not receiving signal.
That's true. Of course If I were to get a vtvm I'd probably have to sink money in to it to get it working right. Probabl...Stormlord5500 — 08:44 PM
Philco model 38 code 121 not receiving signal.
A DMM is good enough. One rarely has to measure indictance, but if you do, short of getting a serious LCR meter (I hav...morzh — 07:35 PM
Testing a speaker and output transformer Trutone A2-G
You guy's are right on. I found a broken wire on the speaker plug that I replaced and all is well now. Have better volu...murf — 03:43 PM
Philco model 38 code 121 not receiving signal.
I need to get a vtvm. I think that little component tester is just more accurate. Plus it shows the inductance which is ...Stormlord5500 — 03:07 PM

[-]
Who's Online
There are currently 888 online users. [Complete List]
» 1 Member(s) | 887 Guest(s)
Avatar

>