Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

record plays at 78 but not 45
#1

Hello,

Just found a cool old 50-1721 in a basement.  I'd love to use it.  It gets a hum at high volume.  It turns but no sound unless its set at high rpm so you hear chipmunks but no sound at the correct speed.  Any ideas?

z
#2

Hi Zeb and welcome to the Phorum,
Several thing come to mind. Would service the chassis by testing tubes and resistors replace foil/paper caps along w/ eletrolyics. This will give you a good starting point to do any further troubleshooting.
The turntable give it a mechanical cleaning and lub. Not uncommon to find deteriorating rubber parts (driving the platen) that will need replacement. Another common issue is a weak cartridge (low output) and low tracking pressure.
After 69yrs these sets aren't a plug and play unit any more.

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#3

Thank you very much... so far that is all a mystery to me so I'll start looking into how to do all that.  I'd love to get it working again.
#4

Whatchu got against chipmunks?!   Icon_lol
#5

Nothing really I just don't chipmunks in my vintage pre-chipmunk turntable
#6

Icon_lol    HA!   ok bud.
Terry is good , smart help.  There's lots of good help here.
#7

Nah just don't have a life.[Image: https://philcoradio.com/phorum/images/sm...on_lol.gif]

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry




Users browsing this thread:
[-]
Recent Posts
Restoration of the Canadian General Electric A-87
Well... The console body has been restored, while the varnish dries reliably I started repairing the chassis.. ...RadioSvit — 07:12 AM
Philco Model 38-7: what caps & resistors do fail typically?
Hello Martin, Welcome aboard our little community what great Model 38-7 Sincerely Richardradiorich — 12:30 AM
Philco Model 38-7: what caps & resistors do fail typically?
Welcome to the Phorum Martin. I count about 9 paper caps, the 3 electrolytic caps and 2-Y2 safety caps to replace th...RodB — 09:44 PM
Part numbers to model cross
Jim, We have this index put together by Dale Cook but I don't think that is quite what you are looking for. The Parts...klondike98 — 09:37 PM
Philco Model 38-7: what caps & resistors do fail typically?
Yep the dim bulb test is OK but I'd definitely replace all those electrolytics before I did it. Since those #47 conden...klondike98 — 09:18 PM
Philco 42-345 Restoration/Repair
The resistor is a 2.2 Meg, it was the last one I hadn't replaced. The broadcast is coming in after replacing it.osanders0311 — 09:09 PM
Philco 42-345 Restoration/Repair
What does the resistor measure? I think it should be 3.3 Meg. If the oscillator coil has continuity and the resistanc...RodB — 09:03 PM
Philco Model 38-7: what caps & resistors do fail typically?
Good idea to check the coils... then I'll get hold of an incadescent light bulb and see what happens when the unit is sw...Musaeum — 08:49 PM
Philco 42-345 Restoration/Repair
I have that same set, ain't too much shortwave I like anyway.....it is a good AM DX set. PaulPaul Philco322 — 08:32 PM
Philco Model 38-7: what caps & resistors do fail typically?
Welcome to the Phorum, Martin! Open a new thread in Philco Electronic Restoration when you begin working on your 38-7. ...GarySP — 08:28 PM

[-]
Who's Online
There are currently 941 online users. [Complete List]
» 1 Member(s) | 940 Guest(s)
Avatar

>