Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

41-295 Developed Intermittent Crackling
#1

I electronically restored a 41-295. It has recently developed a crackling sound. It sometimes levels off when it's tuned to a station, but will excite back up when going down the dial. I have replaced almost all the caps except three mica caps, and I've replaced all the resistors. I've probed around looking for sold solder joints or anything loose, but have not found anything conclusive. Besides the crackling it's a fantastic set. Receives well and sounds wonderful. Any tips from the Philco experts out there on this cracking?
#2

(03-06-2012, 04:37 PM)Sourbone Wrote:  I electronically restored a 41-295. It has recently developed a crackling sound. It sometimes levels off when it's tuned to a station, but will excite back up when going down the dial. I have replaced almost all the caps except three mica caps, and I've replaced all the resistors. I've probed around looking for sold solder joints or anything loose, but have not found anything conclusive. Besides the crackling it's a fantastic set. Receives well and sounds wonderful. Any tips from the Philco experts out there on this cracking?

Could be a bad mica but I'd grab the tracer poke around till I found the problem.
Terry
#3

Only 3 mica caps to go? Replace 'em. But only after the gentle tapping and probing with a dry old chopstick reject from the kitchen. I assume that tube pins, sockets and switches have received their once every 50 years Deoxit shower.

Else you may be poking around until next Christmas.




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco model 38 code 121 not receiving signal.
That's true. Of course If I were to get a vtvm I'd probably have to sink money in to it to get it working right. Probabl...Stormlord5500 — 08:44 PM
Philco model 38 code 121 not receiving signal.
A DMM is good enough. One rarely has to measure indictance, but if you do, short of getting a serious LCR meter (I hav...morzh — 07:35 PM
Testing a speaker and output transformer Trutone A2-G
You guy's are right on. I found a broken wire on the speaker plug that I replaced and all is well now. Have better volu...murf — 03:43 PM
Philco model 38 code 121 not receiving signal.
I need to get a vtvm. I think that little component tester is just more accurate. Plus it shows the inductance which is ...Stormlord5500 — 03:07 PM
Philco model 38 code 121 not receiving signal.
I use a pair of Mastercraft brand DMMs from Canadian Tire, from what I read most of those DMMs use the same main chip re...Arran — 02:36 PM
Philco model 38 code 121 not receiving signal.
Thank you sir. Yes I feel good and also relieved because this one's been weighing on me a bit.Stormlord5500 — 11:18 AM
Philco model 38 code 121 not receiving signal.
It feels good don't it? Good luck on the rest.Paul Philco322 — 11:06 AM
Philco model 38 code 121 not receiving signal.
I've reinstalled the coil. Now IT'S ALIVE!!!!!! I fired up my TinySA on signal generator mode and set it to 1400Kc and ...Stormlord5500 — 11:01 AM
Philco model 38 code 121 not receiving signal.
Yes, Walmart, right up there with Fluke.RodB — 11:00 AM
PT 6 chassis screws size???
it certainly won't be metric! SAE threads were all that was known then. Take care, - GaryGarySP — 10:58 AM

[-]
Who's Online
There are currently 1825 online users. [Complete List]
» 2 Member(s) | 1823 Guest(s)
AvatarAvatar

>