1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
Lamp for Philco 46-427
joegatto
Junior Member
**
Posts: 7
Threads: 2
Joined: Aug 2012
City: South Carolina
#1

03-27-2013, 01:50 PM
The schematic for this set calls for a I100 bulb for the panel light. It is a bayonet type but not a 44 or 47 6 volt bulb. Anyone knowe what it is? Thanks - Joe jdgatto@earthlink.net
Find
Carl Travis
Member
***
Posts: 205
Threads: 6
Joined: Jun 2006
City: Moundsville State, Province, Country: WV
#2

03-27-2013, 02:09 PM
Joe,
P/N 34-2068 is supposed to be a type 47 bulb:
http://www.philcorepairbench.com/lamps.htm
Carl
Northern Panhandle, WV
Find
joegatto
Junior Member
**
Posts: 7
Threads: 2
Joined: Aug 2012
City: South Carolina
#3

03-27-2013, 02:54 PM
Thanks Carl. I see my mistake now. When I first tried a 47 it blew out immediately, probably a fluke. I then went to a 44 but that draws too much current. Will go to radio shack and pick up another 47 and try again. Joe
Find
Chuck Schwark
Phorum Expert
*****
Posts: 1,703
Threads: 55
Joined: Sep 2005
City: Evanston, IL
#4

03-28-2013, 01:26 PM
I100 is the schematic/parts listing designator - Indicator (lamps) 100.

Just like L for coils, T for transformers, C for caps, etc......
Chuck
Chuck Schwark,
The Philco Repair Bench
[Image: http://www.philcorepairbench.com/images/philog3tiny.gif]
http://www.philcorepairbench.com
Website Find
« Next Oldest | Next Newest »
Thread Closed




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM
Philco model 38 code 121 not receiving signal.
Well why not! :lol:Stormlord5500 — 03:14 PM
Philco model 38 code 121 not receiving signal.
Good luck next thing you know you will be winding coils just for the fun of it. DavidDavid — 11:29 AM
Testing a speaker and output transformer Trutone A2-G
morzh Short-circuited turns can be considered as a half-dead transformer. But on this case transformer will hot and s...Vlad95 — 11:01 AM
Testing a speaker and output transformer Trutone A2-G
I am not sure how a transformer could be weak. It could be inadequate, but only when you replace the original with somet...morzh — 09:56 AM

[-]
Who's Online
There are currently 2255 online users. [Complete List]
» 2 Member(s) | 2253 Guest(s)
AvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration