Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

help with Philco phonograph
#1

Hey everyone. I'm sorry if I'm posting this in the wrong section. But I have been looking everywhere online and I cannot find anything on my Philco. I hope someone can help. I would love to restore it. I have attached some pics.

[Image: http://i1125.photobucket.com/albums/l583...sfggqi.jpg]

[Image: http://i1125.photobucket.com/albums/l583...phecep.jpg]

[Image: http://i1125.photobucket.com/albums/l583...xnga1i.jpg]

[Image: http://i1125.photobucket.com/albums/l583...k1hf9d.jpg]
#2

Anyone?
#3

Try to place it in Philco Electronic restoration first, but if no one answered it might be due top the fact no one has anything on it.
You did not list the model; I tried C5-1555 and found nothing.
#4

Hi Shane:
I don't have any info on your phono but a safe bet is it needs a new cartridge and the electrolytic caps inside replaced at the very least. Do you have any kind of electronics knowledge? What are the faults at the moment?

Gregb
#5

No faults just wanting a new needle and to restore the case. And to find any sort of info on it that I can.
#6

You might try connecting with the folks at this web site: http://www.everythingradio.com/NeedlesandCartridges.htm although I have no experience with them. Does your needle/cartridge have any numbers or info on it? If so, that may help identify what you need. Folks on this Phorum have had good luck with West Tech http://www.west-techservices.com/p1.htm in rebuilding cartridges, but the ones I'm thinking of have been older models than yours.
#7

Ok thank you!




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM
Philco model 38 code 121 not receiving signal.
Well here it is. It ain't pretty, but hopefully it'll work. I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM
Philco model 38 code 121 not receiving signal.
Well why not! :lol:Stormlord5500 — 03:14 PM

[-]
Who's Online
There are currently 981 online users. [Complete List]
» 1 Member(s) | 980 Guest(s)
Avatar

>