Posts: 90
Threads: 32
Joined: Oct 2011
City: Nipomo
State, Province, Country: CA
A while back I recapped and cleaned up an RCA 28X and now I've opened up a Delco (United Motors) R-1214 and I see the exact same chassis #RC1002 obviously the same manufacturer. Can you give me some background? I know that RCA held a lot of patents, but who actually assembled these chassis?
Thanks for some insight,
Alan
Posts: 4,377
Threads: 411
Joined: Jun 2011
City: Boston
State, Province, Country: Massachusetts
I have read that Delco was headquartered in Detroit in the GM Building, however manufacturing was done at a plant in Kokomo IN. Some sets were made by other makers, RCA one of them. I have a Delco 1212 and it has an internal antenna eerily similar to an RCA 35X, also uses the same wooden bumpers between antenna and chassis, and has the same knobs as some of my RCA's. So that may be your answer. RCA.
My 1212 is a fine player like most of my other 6 tube RCA sets. Maybe have you tried comparing schematics to a similar RCA from that model year or so?
Good luck,
Paul
Tubetalk1
Posts: 327
Threads: 30
Joined: Jul 2017
City: Hay Lakes, Alberta,Canada
Here in Canada, Philco produced sets sold under the Delco name. They are found with different styles of cabinet, not shared with any Philcos. And any that I have run across are all 32 volt windcharger sets.
Posts: 4,682
Threads: 51
Joined: Sep 2008
City: Sandwick, BC, CA
RCA probably built the chassis in this case, however that was not unique as RCA also built some of the pre war U.S Westinghouse sets. I've never owned a house set under the Delco name, only car radios, and I am pretty certain that the car radios were built by Delco, or at least G.M themselves. I did see at least one Delco radio that a guy had for sale and it did have 1940s era RCA style round knobs, I don't remember if it was a U.S model or not, and quite frankly it was not of interest to me other then the brand name, which was not enough for it to overcome the rather dull and uninspired wooden cabinet it was housed in. It would seem that the more interesting looking Delcos came in Bakelite cabinets from what I have seen in books and in online photo galleries, but as to whom made the chassis I can't say as they rarely show pictures of the inside of any set.
Regards
Arran
Posts: 4,377
Threads: 411
Joined: Jun 2011
City: Boston
State, Province, Country: Massachusetts
How is the 28X working out for you with the elliptical speaker? I have a 28X5 it is a good sounding set.
Paul
Tubetalk1
Posts: 90
Threads: 32
Joined: Oct 2011
City: Nipomo
State, Province, Country: CA
Thanks for the replies. That red painted speaker was the first thing in common between the two chassis that I recognized. With the push-pull and that speaker these are some of the best sounding, powerful table tops I have. Everything is built well and is uncrowded making recapping easy. These are great radios. Although one has pushbuttons and I give up on those, they're a pain in the rear.
Thanks all.
Alan
Posts: 4,377
Threads: 411
Joined: Jun 2011
City: Boston
State, Province, Country: Massachusetts
I am fairly certain you are correct, both RCA's.
Good luck and enjoy them.
Paul
Tubetalk1
Users browsing this thread: 1 Guest(s)
|
Recent Posts
|
Jackson 715 not working
|
Now that you posted the schematic, I don't know why that Sprague electrolytic cap is across the meter, as it is not indi...MrFixr55 — 05:51 PM |
HiFi (Chifi) tube amp build - but my own design.
|
What may be lacking in the PP Tube amps may be the 2nd harmonics, which some, especially RCA back in the day called &quo...MrFixr55 — 05:32 PM |
Jackson 715 not working
|
Usually in an emission tester, the tube under test is measured as if it were a diode. So, some testers connect all the g...RodB — 04:17 PM |
Restoring Philco 37-604C
|
Yep. F5 is green, D5 is Red.
Red is Bad.
Green is Clean.morzh — 01:30 PM |
Jackson 715 not working
|
I did start to do that but I stalled out because I could not figure out how the grid and plate get voltage. In this diag...daveone23 — 11:52 AM |
Restoring Philco 37-604C
|
(Insert Homer Simpson "DOPF" Here.)
When all fails, look at the can. Took the Ron Ramirez advice, red Caig D...MrFixr55 — 09:23 AM |
Philco 91 Speaker Replacement
|
From your text I am not sure if you intend to use the existing speaker with a resistor instead of the field coil.
It wo...morzh — 08:44 AM |
Philco 91 Speaker Replacement
|
My field coil is bad. I am still hoping to find an original, but if I can't I will go with a fitting Philco speaker, 125...dconant — 08:34 AM |
Philco 91 Speaker Replacement
|
As Rod said, it is OK to use a fitting speaker, and then look for an original one.
If you buy a Hammond 125 output tr...morzh — 08:15 AM |
Philco 91 Speaker Replacement
|
Yes, I often have to substitute, then keep an eye out for an original. In the meantime, the radio is working and being e...RodB — 08:02 AM |
Who's Online
|
There are currently no members online. |
|
|