Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Heathkit SG
#1

I recently bought a frequency counter to check my heathkit sig gen and although I restored it several years ago and have had no problems with it when I check it with the counter, as long as the output dial on the gen is set on low the freq is dead on but as I increase the output on the gen the frequency climbs on the counter. Shouldn't the frequency that the gen is set to stay the same no matter how much the output is increased?

Thanks, Todd
#2

The frequency stays the same...but most signal generators put out a fairly weak signal which is too low to properly trigger the counter unless the output is set to a high level. So when you have the output control on your generator set low, the counter gives an inaccurate reading.

Best way to overcome this is to study the schematic of your generator, then install an output jack wired into the generator circuitry ahead of the attenuator controls, so that its level remains high. Connect your freq counter to this new jack.

--
Ron Ramirez
Ferdinand IN
#3

Yep, count varies with output. Get the old generator (and warmed up mind you,) and modern counter to agree, remove the counter, and hope for the best. Probably still better than relying on the printed dial, and "good enough" for most AM jobs. Your results may vary.
#4

I have no problem using this setup.

You raise the output to read steady value that agrees (more or less) with the SG scale, and then lower it appropriately if needed.
I also turn off the modulating signal while setting the frequency.

And yes, both counter and SG should be warmed up for a few minutes.




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Jackson 715 not working
Mrfixr55, its working now. I cleaned the switches and sockets with spray cleaner. Thanks for helping on this one.daveone23 — 06:26 PM
Jackson 715 not working
Now that you posted the schematic, I don't know why that Sprague electrolytic cap is across the meter, as it is not indi...MrFixr55 — 05:51 PM
HiFi (Chifi) tube amp build - but my own design.
What may be lacking in the PP Tube amps may be the 2nd harmonics, which some, especially RCA back in the day called &quo...MrFixr55 — 05:32 PM
Jackson 715 not working
Usually in an emission tester, the tube under test is measured as if it were a diode. So, some testers connect all the g...RodB — 04:17 PM
Restoring Philco 37-604C
Yep. F5 is green, D5 is Red. Red is Bad. Green is Clean.morzh — 01:30 PM
Jackson 715 not working
I did start to do that but I stalled out because I could not figure out how the grid and plate get voltage. In this diag...daveone23 — 11:52 AM
Restoring Philco 37-604C
(Insert Homer Simpson "DOPF" Here.) When all fails, look at the can. Took the Ron Ramirez advice, red Caig D...MrFixr55 — 09:23 AM
Philco 91 Speaker Replacement
From your text I am not sure if you intend to use the existing speaker with a resistor instead of the field coil. It wo...morzh — 08:44 AM
Philco 91 Speaker Replacement
My field coil is bad. I am still hoping to find an original, but if I can't I will go with a fitting Philco speaker, 125...dconant — 08:34 AM
Philco 91 Speaker Replacement
As Rod said, it is OK to use a fitting speaker, and then look for an original one. If you buy a Hammond 125 output tr...morzh — 08:15 AM

[-]
Who's Online
There are currently 4054 online users. [Complete List]
» 1 Member(s) | 4053 Guest(s)
Avatar

>