Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Power supply for 37-33
#1

Will the ARBE-III http://www.radiolaguy.com/RadioPowerSupply.htm work for my 37-33?  I can't be certain based on the information I have read so far, so I am taking the lazy way out and just asking.
#2

kl
yes arblll should work
sam

Some day, and that day may never come, I will call upon you to do a service for me. But until that day, accept this justice as a gift
mafiamen2
#3

(06-26-2015, 11:03 AM)sam Wrote:  kl
yes arblll should work
sam

Thanks Sam!  I had both the cathedral and the floor model and sold the cathedral on ebay (mistake).  But I would like to have the console working. 
#4

Welcome to the Phorum!! Icon_wave
#5

(06-26-2015, 02:01 PM)klondike98 Wrote:  Welcome to the Phorum!!  Icon_wave

Thanks Bob.   I have corresponded with Ron for years but never signed on the Phorum.   Several of the 37 philcos in the gallery are mine.  
#6

Not sure if it will. The 37-33 requires two bias voltages  -3 and -9v. It's simple enough to wire up a battery or two for these voltages. Then all you need is +135v, 90v, and 2v for the filaments. Be sure to throttle back the filament voltage if you have been using the p/s on a set with 01A's.

Terry
ps After looking at the link it should work fine!!!
#7

(06-29-2015, 06:24 AM)Radioroslyn Wrote:  Not sure if it will. The 37-33 requires two bias voltages  -3 and -9v. It's simple enough to wire up a battery or two for these voltages. Then all you need is +135v, 90v, and 2v for the filaments. Be sure to throttle back the filament voltage if you have been using the p/s on a set with 01A's.

Terry
ps After looking at the link it should work fine!!!
Thanks!  I had already ordered it.  I know I could rig it but I am getting lazy in my old age.
#8

It's a good playing set . I've got the table model picked it up 30yrs ago. Was in ruff shape and was missing the spkr. Used an 8"pm  spkr w/a p/p output transformer.

Terry
#9

(06-29-2015, 02:44 PM)Radioroslyn Wrote:  It's a good playing set . I've got the table model picked it up 30yrs ago. Was in ruff shape and was missing the spkr. Used an 8"pm  spkr w/a p/p output transformer.

Terry
Terry,

 
I had both the cathedral and floor models of the 37-33 and decided to part with the cathedral as the cabinet is the same as several other models I have on display.  BUT  it sold for less than $30 on ebay and it was in excellent condition.  
KLB




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Jackson 715 not working
Now that you posted the schematic, I don't know why that Sprague electrolytic cap is across the meter, as it is not indi...MrFixr55 — 05:51 PM
HiFi (Chifi) tube amp build - but my own design.
What may be lacking in the PP Tube amps may be the 2nd harmonics, which some, especially RCA back in the day called &quo...MrFixr55 — 05:32 PM
Jackson 715 not working
Usually in an emission tester, the tube under test is measured as if it were a diode. So, some testers connect all the g...RodB — 04:17 PM
Restoring Philco 37-604C
Yep. F5 is green, D5 is Red. Red is Bad. Green is Clean.morzh — 01:30 PM
Jackson 715 not working
I did start to do that but I stalled out because I could not figure out how the grid and plate get voltage. In this diag...daveone23 — 11:52 AM
Restoring Philco 37-604C
(Insert Homer Simpson "DOPF" Here.) When all fails, look at the can. Took the Ron Ramirez advice, red Caig D...MrFixr55 — 09:23 AM
Philco 91 Speaker Replacement
From your text I am not sure if you intend to use the existing speaker with a resistor instead of the field coil. It wo...morzh — 08:44 AM
Philco 91 Speaker Replacement
My field coil is bad. I am still hoping to find an original, but if I can't I will go with a fitting Philco speaker, 125...dconant — 08:34 AM
Philco 91 Speaker Replacement
As Rod said, it is OK to use a fitting speaker, and then look for an original one. If you buy a Hammond 125 output tr...morzh — 08:15 AM
Philco 91 Speaker Replacement
Yes, I often have to substitute, then keep an eye out for an original. In the meantime, the radio is working and being e...RodB — 08:02 AM

[-]
Who's Online
There are currently no members online.

>