Posts: 7,283
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
The reason why it does that is that the filament in these sets (ac/dc) are connected in series along w/the lamp. The cold resistance of these is lower than when they are hot (after 10 or 15 seconds of warmup) Cold more current passes thru lamp yielding a brighter illumination. As the filament warms the resistance increase and less current passes thru the lamp yielding less brightness. That's the long answer.
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!
Terry
(This post was last modified: 07-08-2017, 08:17 PM by Radioroslyn.)
Posts: 24
Threads: 8
Joined: Feb 2017
City: Timonium, MD
Sounds good Bob. Mine dims out completely after a minute or two. I thought it would look pretty cool if it stayed even slightly lit.
Posts: 5,072
Threads: 269
Joined: Nov 2012
City: Bandon
State, Province, Country: OR
Back to working on this Emerson 250AW. I've toned the cabinet and started the gloss lacquer coatings. Will have pics of that when I've finished it and put it all back together.
When I was at Kutztown last May I came across a restored 250AW set by a fellow in the other pavillion. I took his card but have managed to lose it and for the life of me can't remember his name. His restorations were absolutely beautiful but the 250AW caught my eye since I was also working on one. Here's a pic of his radio (not mine) which he gave me permission to photograph. I'm sure Ron knows this fellow as he's been a regular at KTown.
[Image: https://www.dropbox.com/s/hmn6av8wt5lw0w....jpg?raw=1]
What really caught my eye in addition to the nice finish was the treatment of the brass plates. He painted them black and then took the paint off the raised lettering to give the really sharp looking brass on black look. I thought I'd give that treatment a try and was pleasantly surprised by the first attempt. First pic shows the brass plate painted black and the strip of 320 grit sandpaper on the pencil that I used to tease the paint off the raised lettering. Its a slow process but not overly difficult. Its easy to sand off paint around the edges of the plate if not careful, but a small brush and touch up took care of that without having to start over. When finished taking the paint off I just hit it with clear lacquer. That took care of protecting everything and adding gloss to the portions of the black paint that had gotten scuffed up. The other two plates are in progress.
[Image: https://www.dropbox.com/s/1qq3t158zcoiqg....jpg?raw=1]
[Image: https://www.dropbox.com/s/2ybny5sr4fwebe....jpg?raw=1]
Posts: 7,283
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
Really makes it POP!!
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!
Terry
Posts: 3,138
Threads: 56
Joined: Apr 2011
City: Lexington, KY
(08-19-2017, 10:49 AM)klondike98 Wrote: .......When I was at Kutztown last May I came across a restored 250AW set by a fellow in the other pavillion. I took his card but have managed to lose it and for the life of me can't remember his name. His restorations were absolutely beautiful but the 250AW caught my eye since I was also working on one........
Bob, I'm pretty sure that booth was Tom Hayes from Alabama, and he does do absolutely beautiful work. He also sells on Radio Attic if you want to contact him...
John KK4ZLF
Lexington, KY
"illegitimis non carborundum"
Posts: 4,107
Threads: 310
Joined: Nov 2013
City: Kings Park NY
Yup that is Tom..
Times I have been electrocuted in 2021
As of 1/01/2021
AC: 4 DC: 1
Last year: 6
Posts: 5,072
Threads: 269
Joined: Nov 2012
City: Bandon
State, Province, Country: OR
Tom Hayes....OK! Thanks guys!
Posts: 5,072
Threads: 269
Joined: Nov 2012
City: Bandon
State, Province, Country: OR
Its not Tom Hayes quality but I'm pleased with the way it did turn out. Unfortunately mine does not have the back to it although it could be reproduced with some effort...but that's another day some time in the distant future
[Image: https://www.dropbox.com/s/553x6wvjhsiupl....jpg?raw=1]
Posts: 3,138
Threads: 56
Joined: Apr 2011
City: Lexington, KY
Looks good Bob
The reason Tom's radios turn out so nice is he's an ex-car painter, so he has the equipment and skills to use it properly.
John KK4ZLF
Lexington, KY
"illegitimis non carborundum"
Posts: 4,107
Threads: 310
Joined: Nov 2013
City: Kings Park NY
Yup,
He is a perfectionist but yours is pretty much the same. It is a little more glossy but some pumice would make the finish just as smooth. Remember gloss shows more imperfections..
I think it is a beauty. There is one locally for $220.00 in not great condition...
It will sit there for a long time..
Times I have been electrocuted in 2021
As of 1/01/2021
AC: 4 DC: 1
Last year: 6
Posts: 667
Threads: 11
Joined: Sep 2014
City: Bellmawr, NJ
Very Profession job,,,,Keep up the Great work,,,CHEERS
Users browsing this thread: 1 Guest(s)
|
Recent Posts
|
Jackson 715 not working
|
Mrfixr55, its working now. I cleaned the switches and sockets with spray cleaner. Thanks for helping on this one.daveone23 — 06:26 PM |
Jackson 715 not working
|
Now that you posted the schematic, I don't know why that Sprague electrolytic cap is across the meter, as it is not indi...MrFixr55 — 05:51 PM |
HiFi (Chifi) tube amp build - but my own design.
|
What may be lacking in the PP Tube amps may be the 2nd harmonics, which some, especially RCA back in the day called &quo...MrFixr55 — 05:32 PM |
Jackson 715 not working
|
Usually in an emission tester, the tube under test is measured as if it were a diode. So, some testers connect all the g...RodB — 04:17 PM |
Restoring Philco 37-604C
|
Yep. F5 is green, D5 is Red.
Red is Bad.
Green is Clean.morzh — 01:30 PM |
Jackson 715 not working
|
I did start to do that but I stalled out because I could not figure out how the grid and plate get voltage. In this diag...daveone23 — 11:52 AM |
Restoring Philco 37-604C
|
(Insert Homer Simpson "DOPF" Here.)
When all fails, look at the can. Took the Ron Ramirez advice, red Caig D...MrFixr55 — 09:23 AM |
Philco 91 Speaker Replacement
|
From your text I am not sure if you intend to use the existing speaker with a resistor instead of the field coil.
It wo...morzh — 08:44 AM |
Philco 91 Speaker Replacement
|
My field coil is bad. I am still hoping to find an original, but if I can't I will go with a fitting Philco speaker, 125...dconant — 08:34 AM |
Philco 91 Speaker Replacement
|
As Rod said, it is OK to use a fitting speaker, and then look for an original one.
If you buy a Hammond 125 output tr...morzh — 08:15 AM |
Who's Online
|
There are currently 4018 online users. [Complete List] » 1 Member(s) | 4017 Guest(s)
|
|
|
|