Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Heathkit VTVM
#16

Fixed did?
#17

Warren I have a old radio shack Hatitachi(sp) VTVM from around 1968 which I purchased new. Ok I am getting old! When new would take around 15 minutes of warm up before you could trust the readings. Recap a few years ago check resistors still takes a good 15 minutes warm up. David
#18

Codefox .. No, its not fixed yet.. my work doesnt allow me much time to do these things, but hopefully I will try these things soon. I am also ordering new caps and resistors to recap it. I will let you know what I find soon.. Thanks for wondering.
#19

A lot of the resistors should be precision wire wound, not needing replacement.

"I just might turn into smoke, but I feel fine"
http://www.russoldradios.com/
#20

I would say your V2 is not conducting based on what you have described.

I would clean the pins of the socket V2. Make sure the pins 1,6 have connection to the D1 and R29, and C6

I would check D1 and all resistors common to both sides of the V2 : R23 - R30

If I found no problems I would insure the transformer is putting out 120VAC not connected to the circuit.

Then I would start looking at and around M1.
#21

Thanks for everyones suggestions.. I might not get to checking it until next week, i am oncall for my job this week but I will try the suggestions and let you all know what happens, thanks again.
#22

Whatever, it's nice to have an analog meter when doing alignments, as digital ones stutter, stutter, got it? Good mostly for relative values, but good enough for most work. Gosh, must have been 50 years ago when I built one, or was it an Eico. To quote, "I just can't recall."
#23

Old VTVM's are great for alignments, as they do not "stutter" while tuning. Otherwise, fine and when warmed up, pretty good for relative readings. Usually battery leaks and voied ohms readings, and leaks further to take out a few more components. So long as meter movement is still good, can be saved pretty easily in an afternoon for a few bucks. Best of luck.




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Jackson 715 not working
Now that you posted the schematic, I don't know why that Sprague electrolytic cap is across the meter, as it is not indi...MrFixr55 — 05:51 PM
HiFi (Chifi) tube amp build - but my own design.
What may be lacking in the PP Tube amps may be the 2nd harmonics, which some, especially RCA back in the day called &quo...MrFixr55 — 05:32 PM
Jackson 715 not working
Usually in an emission tester, the tube under test is measured as if it were a diode. So, some testers connect all the g...RodB — 04:17 PM
Restoring Philco 37-604C
Yep. F5 is green, D5 is Red. Red is Bad. Green is Clean.morzh — 01:30 PM
Jackson 715 not working
I did start to do that but I stalled out because I could not figure out how the grid and plate get voltage. In this diag...daveone23 — 11:52 AM
Restoring Philco 37-604C
(Insert Homer Simpson "DOPF" Here.) When all fails, look at the can. Took the Ron Ramirez advice, red Caig D...MrFixr55 — 09:23 AM
Philco 91 Speaker Replacement
From your text I am not sure if you intend to use the existing speaker with a resistor instead of the field coil. It wo...morzh — 08:44 AM
Philco 91 Speaker Replacement
My field coil is bad. I am still hoping to find an original, but if I can't I will go with a fitting Philco speaker, 125...dconant — 08:34 AM
Philco 91 Speaker Replacement
As Rod said, it is OK to use a fitting speaker, and then look for an original one. If you buy a Hammond 125 output tr...morzh — 08:15 AM
Philco 91 Speaker Replacement
Yes, I often have to substitute, then keep an eye out for an original. In the meantime, the radio is working and being e...RodB — 08:02 AM

[-]
Who's Online
There are currently 4043 online users. [Complete List]
» 2 Member(s) | 4041 Guest(s)
AvatarAvatar

>