Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Have Philco Transitone T-3
#1

Looking for schematic and service information for a Philco Transitone T-3. Also may be known as a Studibaker-Philco ST-3. 6 Tubes and 1 large 4-pin 6V vibrator. Most usual sites have been dead-end. Beitman and Raider no go as well or I am  not looking it up correctly.
NOTE: Chassis Model T3 Code 121

Dave KB7GP


Attached Files Image(s)
                   
#2

Welcome to the Phorum Dave!

It looks like the picture attachments are missing from your message. You can try adding them again by clicking the 'Edit' button followed by 'Full Edit'.

As for the service information, your best bet would be Chuck Schwark at philcorepairbench.com:

http://www.philcorepairbench.com/schematics.htm

He provides excellent quality copies of Philco service information.
#3

(04-02-2017, 10:39 PM)Nathan Slingerland Wrote:  Welcome to the Phorum Dave!

It looks like the picture attachments are missing from your message. You can try adding them again by clicking the 'Edit' button followed by 'Full Edit'.

As for the service information, your best bet would be Chuck Schwark at philcorepairbench.com:

http://www.philcorepairbench.com/schematics.htm

He provides excellent quality copies of Philco service information.

Hey thank you... Don't understand. when I prevued the post everything was fine.
Does this sound like a number you may have in your files? I will try to see where the attachments went.
#4

Ok it looks like the attachments are there now ??
Dave
#5

Yup - not sure what happened, but the pictures are there now. Icon_thumbup
#6

I have several Riders Volumes. I can check tonight after work to see if I have it. Nostalgia Air may not have posted the complete info for some reason, but I noticed while looking through my Riders that they are covered. Service info is there, but the schematic is not on Nostalgia Air.

http://www.nostalgiaair.org/Resources/222/M0014222.htm

Blessings,
Jeff W.
Jonesboro, Arkansas

http://jeffsradios.weebly.com

God loves you as you are, not as you should be, because none of us are as we should be. - Brennan Manning
#7

Nathan's suggestion is probably the way to go. I just checked and my Riders was the same as what Nostalgia Air had, unfortunately.

Blessings,
Jeff W.
Jonesboro, Arkansas

http://jeffsradios.weebly.com

God loves you as you are, not as you should be, because none of us are as we should be. - Brennan Manning




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Jackson 715 not working
Now that you posted the schematic, I don't know why that Sprague electrolytic cap is across the meter, as it is not indi...MrFixr55 — 05:51 PM
HiFi (Chifi) tube amp build - but my own design.
What may be lacking in the PP Tube amps may be the 2nd harmonics, which some, especially RCA back in the day called &quo...MrFixr55 — 05:32 PM
Jackson 715 not working
Usually in an emission tester, the tube under test is measured as if it were a diode. So, some testers connect all the g...RodB — 04:17 PM
Restoring Philco 37-604C
Yep. F5 is green, D5 is Red. Red is Bad. Green is Clean.morzh — 01:30 PM
Jackson 715 not working
I did start to do that but I stalled out because I could not figure out how the grid and plate get voltage. In this diag...daveone23 — 11:52 AM
Restoring Philco 37-604C
(Insert Homer Simpson "DOPF" Here.) When all fails, look at the can. Took the Ron Ramirez advice, red Caig D...MrFixr55 — 09:23 AM
Philco 91 Speaker Replacement
From your text I am not sure if you intend to use the existing speaker with a resistor instead of the field coil. It wo...morzh — 08:44 AM
Philco 91 Speaker Replacement
My field coil is bad. I am still hoping to find an original, but if I can't I will go with a fitting Philco speaker, 125...dconant — 08:34 AM
Philco 91 Speaker Replacement
As Rod said, it is OK to use a fitting speaker, and then look for an original one. If you buy a Hammond 125 output tr...morzh — 08:15 AM
Philco 91 Speaker Replacement
Yes, I often have to substitute, then keep an eye out for an original. In the meantime, the radio is working and being e...RodB — 08:02 AM

[-]
Who's Online
There are currently no members online.

>