Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

1960's Panasonic from an estate sale
#1

I was at an estate sale today, and I saw this real nice Panasonic RE-7371. It was just begging me to take it home, and for $10, I just couldn't pass it up. It's in excellent condition, and it sounds beautiful. It's pretty nice to be in the FM world again, too.

   

Slave to an RCA Victor CTC-25
#2

For 10 bucks, sure, could always use another tuner.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#3

I hit it with the old GOJO Creme, and YOWZA! That GOJO Creme made it look like brand new!


Attached Files Image(s)
   

Slave to an RCA Victor CTC-25
#4

Better than any AM/FM you could get today for the money. Why was it filmed on the toilet tank?

Paul

Tubetalk1
#5

Didn't you know I collect toilets? These are three of my nicest Kohlers.


Attached Files Image(s)
   

Slave to an RCA Victor CTC-25
#6

My 1959 Kohler Wellworth. Sorry, I couldn't get all three in the picture.


Attached Files Image(s)
   

Slave to an RCA Victor CTC-25
#7

And vintage vacuums I see too. Many plumbers in my family, they were all skeptical of the low flush toilets. A vintage bowl was a quality bowl. I have seen how the vitreous is made and fired and I find it very interesting.

Paul

Tubetalk1
#8

Is there any particular reason why when I click this radio off, it blasts the station back at me for about 2 seconds and slowly fades away? Sometimes it changes stations during the fade. It works great, but this is getting annoying. The blast is so loud, it can be heard on the other side of the house. I'm scared it's going to hurt the speaker if it continues.

Slave to an RCA Victor CTC-25
#9

 First of all it is not from the 1960s, probably more like the early 1970s, before 1970 the Jap makes used to mark the dial frequencies in KC and MC not KHz and MHz, if you open it up you may find some date codes that will narrow it down. As for the other issue with the volume blast when you turn it of chances are it needs the electrolytics changed and maybe a few resistors by now.
Regards
Arran




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Jackson 715 not working
Mrfixr55, its working now. I cleaned the switches and sockets with spray cleaner. Thanks for helping on this one.daveone23 — 06:26 PM
Jackson 715 not working
Now that you posted the schematic, I don't know why that Sprague electrolytic cap is across the meter, as it is not indi...MrFixr55 — 05:51 PM
HiFi (Chifi) tube amp build - but my own design.
What may be lacking in the PP Tube amps may be the 2nd harmonics, which some, especially RCA back in the day called &quo...MrFixr55 — 05:32 PM
Jackson 715 not working
Usually in an emission tester, the tube under test is measured as if it were a diode. So, some testers connect all the g...RodB — 04:17 PM
Restoring Philco 37-604C
Yep. F5 is green, D5 is Red. Red is Bad. Green is Clean.morzh — 01:30 PM
Jackson 715 not working
I did start to do that but I stalled out because I could not figure out how the grid and plate get voltage. In this diag...daveone23 — 11:52 AM
Restoring Philco 37-604C
(Insert Homer Simpson "DOPF" Here.) When all fails, look at the can. Took the Ron Ramirez advice, red Caig D...MrFixr55 — 09:23 AM
Philco 91 Speaker Replacement
From your text I am not sure if you intend to use the existing speaker with a resistor instead of the field coil. It wo...morzh — 08:44 AM
Philco 91 Speaker Replacement
My field coil is bad. I am still hoping to find an original, but if I can't I will go with a fitting Philco speaker, 125...dconant — 08:34 AM
Philco 91 Speaker Replacement
As Rod said, it is OK to use a fitting speaker, and then look for an original one. If you buy a Hammond 125 output tr...morzh — 08:15 AM

[-]
Who's Online
There are currently no members online.

>