Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Precision E-200-C
#18

Making progress on the E-200-C. I had a broken RF selector switch which is why I had no real output. Fixed that and continued to replace bad out of tolerance resistors and wax caps. Now I ran into a problem of my own doing. Replaced the old resistors under the 6AU6 tube, but to do so I had to disconnect several points. I thought I had good photos of all areas but I neglected one and that connection has me stumped. It is a bare wire lead from the lowest wafer in the stack located between band coils B and C. This lead runs up through the next two wafers and connects somewhere in the tube socket area. I just cant determine where. Anyone have theirs open that can send me a photo?


Attached Files Image(s)
       


Messages In This Thread
Precision E-200-C - by Mike L - 09-17-2016, 06:48 PM
RE: Precision E-200-C - by KCMike - 09-17-2016, 08:50 PM
RE: Precision E-200-C - by Bradley Rush - 11-20-2016, 10:33 PM
RE: Precision E-200-C - by Bradley Rush - 11-21-2016, 12:34 AM
RE: Precision E-200-C - by Mike L - 11-21-2016, 07:49 PM
RE: Precision E-200-C - by KCMike - 11-21-2016, 10:44 PM
RE: Precision E-200-C - by Radioroslyn - 11-21-2016, 11:35 PM
RE: Precision E-200-C - by morzh - 11-22-2016, 11:00 AM
RE: Precision E-200-C - by Radioroslyn - 11-22-2016, 01:21 PM
RE: Precision E-200-C - by morzh - 11-22-2016, 01:26 PM
RE: Precision E-200-C - by Radioroslyn - 11-22-2016, 03:00 PM
RE: Precision E-200-C - by morzh - 11-22-2016, 03:10 PM
RE: Precision E-200-C - by Mondial - 11-23-2016, 09:22 PM
RE: Precision E-200-C - by Radioroslyn - 11-24-2016, 08:10 AM
RE: Precision E-200-C - by Mondial - 11-24-2016, 09:34 AM
RE: Precision E-200-C - by Radioroslyn - 11-24-2016, 11:36 AM
RE: Precision E-200-C - by Mike L - 11-26-2016, 04:32 PM
RE: Precision E-200-C - by Mike L - 12-24-2016, 02:40 PM
RE: Precision E-200-C - by Radioroslyn - 12-24-2016, 03:41 PM
RE: Precision E-200-C - by Mike L - 12-24-2016, 04:49 PM
RE: Precision E-200-C - by Radioroslyn - 12-24-2016, 06:06 PM
RE: Precision E-200-C - by Mike L - 12-31-2016, 08:33 AM
RE: Precision E-200-C - by Radioroslyn - 12-31-2016, 11:55 PM
RE: Precision E-200-C - by Mike L - 01-01-2017, 04:27 PM
RE: Precision E-200-C - by JLuke - 07-27-2024, 11:33 AM
RE: Precision E-200-C - by DaleHCook - 07-28-2024, 10:29 AM
RE: Precision E-200-C - by RodB - 07-28-2024, 03:59 PM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Jackson 715 not working
Mrfixr55, its working now. I cleaned the switches and sockets with spray cleaner. Thanks for helping on this one.daveone23 — 06:26 PM
Jackson 715 not working
Now that you posted the schematic, I don't know why that Sprague electrolytic cap is across the meter, as it is not indi...MrFixr55 — 05:51 PM
HiFi (Chifi) tube amp build - but my own design.
What may be lacking in the PP Tube amps may be the 2nd harmonics, which some, especially RCA back in the day called &quo...MrFixr55 — 05:32 PM
Jackson 715 not working
Usually in an emission tester, the tube under test is measured as if it were a diode. So, some testers connect all the g...RodB — 04:17 PM
Restoring Philco 37-604C
Yep. F5 is green, D5 is Red. Red is Bad. Green is Clean.morzh — 01:30 PM
Jackson 715 not working
I did start to do that but I stalled out because I could not figure out how the grid and plate get voltage. In this diag...daveone23 — 11:52 AM
Restoring Philco 37-604C
(Insert Homer Simpson "DOPF" Here.) When all fails, look at the can. Took the Ron Ramirez advice, red Caig D...MrFixr55 — 09:23 AM
Philco 91 Speaker Replacement
From your text I am not sure if you intend to use the existing speaker with a resistor instead of the field coil. It wo...morzh — 08:44 AM
Philco 91 Speaker Replacement
My field coil is bad. I am still hoping to find an original, but if I can't I will go with a fitting Philco speaker, 125...dconant — 08:34 AM
Philco 91 Speaker Replacement
As Rod said, it is OK to use a fitting speaker, and then look for an original one. If you buy a Hammond 125 output tr...morzh — 08:15 AM

[-]
Who's Online
There are currently no members online.

>