Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Starting 37-116 Deluxe Restoration
#61

I have the original mounting hardware on mine. There is a 3/4" diameter rubber washer about 1/4" thick on the sleeve and that's it. The sleeve and screw go through the cabinet hole with no grommet and the washer keeps it from pulling through. The chassis just floats on the four rubber washers and the sleeve and screw just keep it from lifting off or sliding back.

I had a bit of a problem with the washers from RR. They seem to be very soft and compress too much on the heavier end with the power transformer, so the chassis tilts lower on that side. Placed some cardboard under that side of the chassis until I come up with a better solution.


Messages In This Thread
Starting 37-116 Deluxe Restoration - by Nick3092 - 08-28-2014, 10:49 AM
RE: Starting 37-116 Deluxe Restoration - by morzh - 08-28-2014, 12:46 PM
RE: Starting 37-116 Deluxe Restoration - by morzh - 08-28-2014, 01:43 PM
RE: Starting 37-116 Deluxe Restoration - by morzh - 08-28-2014, 04:53 PM
RE: Starting 37-116 Deluxe Restoration - by morzh - 10-11-2014, 06:40 PM
RE: Starting 37-116 Deluxe Restoration - by morzh - 10-12-2014, 08:22 PM
RE: Starting 37-116 Deluxe Restoration - by morzh - 10-14-2014, 06:31 PM
RE: Starting 37-116 Deluxe Restoration - by morzh - 10-17-2014, 02:56 PM
RE: Starting 37-116 Deluxe Restoration - by morzh - 10-18-2014, 01:05 PM
RE: Starting 37-116 Deluxe Restoration - by morzh - 10-18-2014, 06:18 PM
RE: Starting 37-116 Deluxe Restoration - by morzh - 10-18-2014, 06:36 PM
RE: Starting 37-116 Deluxe Restoration - by morzh - 10-18-2014, 09:16 PM
RE: Starting 37-116 Deluxe Restoration - by morzh - 10-19-2014, 06:38 PM
RE: Starting 37-116 Deluxe Restoration - by morzh - 10-29-2014, 08:12 PM
RE: Starting 37-116 Deluxe Restoration - by gvel - 11-02-2014, 05:52 PM
RE: Starting 37-116 Deluxe Restoration - by Mondial - 11-04-2014, 12:10 AM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Jackson 715 not working
Mrfixr55, its working now. I cleaned the switches and sockets with spray cleaner. Thanks for helping on this one.daveone23 — 06:26 PM
Jackson 715 not working
Now that you posted the schematic, I don't know why that Sprague electrolytic cap is across the meter, as it is not indi...MrFixr55 — 05:51 PM
HiFi (Chifi) tube amp build - but my own design.
What may be lacking in the PP Tube amps may be the 2nd harmonics, which some, especially RCA back in the day called &quo...MrFixr55 — 05:32 PM
Jackson 715 not working
Usually in an emission tester, the tube under test is measured as if it were a diode. So, some testers connect all the g...RodB — 04:17 PM
Restoring Philco 37-604C
Yep. F5 is green, D5 is Red. Red is Bad. Green is Clean.morzh — 01:30 PM
Jackson 715 not working
I did start to do that but I stalled out because I could not figure out how the grid and plate get voltage. In this diag...daveone23 — 11:52 AM
Restoring Philco 37-604C
(Insert Homer Simpson "DOPF" Here.) When all fails, look at the can. Took the Ron Ramirez advice, red Caig D...MrFixr55 — 09:23 AM
Philco 91 Speaker Replacement
From your text I am not sure if you intend to use the existing speaker with a resistor instead of the field coil. It wo...morzh — 08:44 AM
Philco 91 Speaker Replacement
My field coil is bad. I am still hoping to find an original, but if I can't I will go with a fitting Philco speaker, 125...dconant — 08:34 AM
Philco 91 Speaker Replacement
As Rod said, it is OK to use a fitting speaker, and then look for an original one. If you buy a Hammond 125 output tr...morzh — 08:15 AM

[-]
Who's Online
There are currently 3909 online users. [Complete List]
» 1 Member(s) | 3908 Guest(s)
Avatar

>