Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

A PITA recap job
#12

Arran,

same case for me, the first time I looked at it, I thought it was a Delon doubler, and the schematic drawing is PITA to read, all garbled, and I was about to make a fool of myself by writing a comment to that effect, when something caught my eye and told me to take another look....nope, no multiplier, just a separate field coil rectifier and filtered ground. Ug-lee.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.


Messages In This Thread
A PITA recap job - by OldRestorer - 06-29-2015, 02:26 PM
RE: A PITA recap job - by morzh - 06-29-2015, 03:10 PM
RE: A PITA recap job - by OldRestorer - 06-29-2015, 03:12 PM
RE: A PITA recap job - by morzh - 06-29-2015, 03:13 PM
RE: A PITA recap job - by Radioroslyn - 06-29-2015, 03:37 PM
RE: A PITA recap job - by morzh - 06-29-2015, 03:53 PM
RE: A PITA recap job - by OldRestorer - 06-30-2015, 10:07 AM
RE: A PITA recap job - by Radioroslyn - 06-30-2015, 01:52 PM
RE: A PITA recap job - by OldRestorer - 06-30-2015, 05:46 PM
RE: A PITA recap job - by Radioroslyn - 06-30-2015, 06:18 PM
RE: A PITA recap job - by Arran - 07-01-2015, 03:30 AM
RE: A PITA recap job - by morzh - 07-01-2015, 08:35 AM
RE: A PITA recap job - by OldRestorer - 07-01-2015, 08:59 AM
RE: A PITA recap job - by OldRestorer - 07-01-2015, 09:31 AM
RE: A PITA recap job - by sam - 07-01-2015, 11:10 AM
RE: A PITA recap job - by morzh - 07-01-2015, 12:19 PM
RE: A PITA recap job - by Radioroslyn - 07-01-2015, 03:46 PM
RE: A PITA recap job - by morzh - 07-01-2015, 03:47 PM
RE: A PITA recap job - by OldRestorer - 07-01-2015, 05:14 PM
RE: A PITA recap job - by OldRestorer - 07-01-2015, 08:09 PM
RE: A PITA recap job - by sam - 07-01-2015, 09:50 PM
RE: A PITA recap job - by OldRestorer - 07-02-2015, 07:55 AM
RE: A PITA recap job - by morzh - 07-02-2015, 08:10 AM
RE: A PITA recap job - by sam - 07-02-2015, 11:23 AM
RE: A PITA recap job - by OldRestorer - 07-02-2015, 02:55 PM
RE: A PITA recap job - by Radioroslyn - 07-05-2015, 08:53 PM
RE: A PITA recap job - by sam - 07-05-2015, 09:30 PM
RE: A PITA recap job - by morzh - 07-06-2015, 09:09 AM
RE: A PITA recap job - by sam - 07-06-2015, 10:45 AM
RE: A PITA recap job - by Radioroslyn - 07-06-2015, 11:41 AM
RE: A PITA recap job - by sam - 07-06-2015, 11:50 AM
RE: A PITA recap job - by morzh - 07-06-2015, 12:19 PM
RE: A PITA recap job - by Radioroslyn - 07-06-2015, 03:54 PM
RE: A PITA recap job - by morzh - 07-06-2015, 06:06 PM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
RCA WV-98c
If this is R22, check the voltage on the wiper (86V). If this is R33, see if the lower pin indeed connected to GND, the ...morzh — 02:29 PM
Philco 38-2 Low Volume
Both sch, the one you showed in the beginning and the one I see on Nostalgia, show 40K for the 2nd audio plate.morzh — 02:25 PM
Model 96 cabinet veneer
I can't figure out what the first step is, let alone the final step. I have tried copying pictures from my hard drive a...TGLager — 01:40 PM
Philco 38-2 Low Volume
I managed to get some more time on this. Hi Mr. FixIT, The radio has been recapped. Many of the resistors were rep...dconant — 01:39 PM
Philco 38-2 Low Volume
Thanks guys for the help. I started looking at these points but I have to quit for the day. I will be looking into this ...dconant — 12:23 PM
RCA WV-98c
Check out this crazy zero pot operation. Touching it drives it crazy. Its rubber tipped. Also the 6al5 has no negative v...daveone23 — 12:08 PM
Philco 38-2 Low Volume
If you check all of that and still have a problem (my first inkling would be one of the 6F6s) then look at the 6J5 phase...RodB — 10:44 AM
RCA WV-98c
Those will probably depend on teh switch combination. Could you list some that you see, their values and what they sh...morzh — 10:26 AM
Model 96 cabinet veneer
You are probably skipping the final step. Once you select the photos you want and they get downloaded, the system assign...RodB — 09:36 AM
RCA WV-98c
At this point, there is no input, just internal voltages Which are incorrect and not sure what they should be.daveone23 — 09:15 AM

[-]
Who's Online
There are currently 1747 online users. [Complete List]
» 1 Member(s) | 1746 Guest(s)
Avatar

>