Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco 37-620
#1

Hello everyone. I'm new here.  I hope you all have a great New Year!!  I've been reading some of the posts and was looking for some advice.  About 20 years ago I bought a Philco 37-620 in good condition. Just needed some cosmetics. I ran a couple of "tandum" wires where I saw questionable wiring on top (and replaced the power cord) the year I bought it.  You can see them in the picture (but left original wires in place). It has worked great for years. Here is the advice I need.  If it works fine...should I change out any components like capacitors for potential fire hazard?

I have it out of the cabinet to repair the speaker cone (mover put a finger through it)  Thank you for your help!

Alan
Burrke, VA


Attached Files Image(s)
           


Messages In This Thread
Philco 37-620 - by Alan - 12-27-2017, 08:15 PM
RE: Philco 37-620 - by Radioroslyn - 12-27-2017, 08:56 PM
RE: Philco 37-620 - by klondike98 - 12-27-2017, 09:08 PM
RE: Philco 37-620 - by Alan - 12-28-2017, 12:02 AM
RE: Philco 37-620 - by morzh - 12-28-2017, 12:11 AM
RE: Philco 37-620 - by Radioroslyn - 12-28-2017, 01:51 AM
RE: Philco 37-620 - by Alan - 12-30-2017, 10:23 PM
RE: Philco 37-620 - by Alan - 12-30-2017, 10:35 PM
RE: Philco 37-620 - by Radioroslyn - 12-30-2017, 10:55 PM
RE: Philco 37-620 - by Alan - 01-07-2018, 09:33 PM
RE: Philco 37-620 - by klondike98 - 01-08-2018, 08:59 AM
RE: Philco 37-620 - by Alan - 01-08-2018, 09:29 PM
RE: Philco 37-620 - by klondike98 - 01-08-2018, 09:39 PM
RE: Philco 37-620 - by Ron Ramirez - 01-09-2018, 06:27 AM
RE: Philco 37-620 - by klondike98 - 01-09-2018, 09:16 AM
RE: Philco 37-620 - by Alan - 01-09-2018, 09:54 PM
RE: Philco 37-620 - by klondike98 - 01-09-2018, 10:04 PM
RE: Philco 37-620 - by Radioroslyn - 01-09-2018, 10:23 PM
RE: Philco 37-620 - by Alan - 01-10-2018, 06:19 AM
RE: Philco 37-620 - by Ron Ramirez - 01-10-2018, 06:23 AM
RE: Philco 37-620 - by Alan - 01-10-2018, 10:32 PM
RE: Philco 37-620 - by Radioroslyn - 01-11-2018, 11:21 AM
RE: Philco 37-620 - by Ron Ramirez - 01-11-2018, 11:46 AM
RE: Philco 37-620 - by Alan - 01-11-2018, 09:28 PM
RE: Philco 37-620 - by Arran - 01-11-2018, 11:02 PM
RE: Philco 37-620 - by Alan - 01-14-2018, 09:59 PM



Users browsing this thread: 1 Guest(s)