Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Doubts with 80jr model
#1

Hello, I bought a model 80 B. and the variable capacitor has 10 sheets in each section and has room for one more. I have seen many pictures and all I see are 11 per section. There are several models? I also see some who have the square cans and other round coils. could be oldest round? a greeting
#2

Welcome to the Phorum. If you could post some pictures that would be nice.
Sounds like you mean the plates of the variable capacitor. I'm sure someone on here can help you with your questions.
#3

Welcome to the Phorum!
Icon_wave 

The tuner capacitor in my 80 has 10 plates in each of the two rotor sections (the part the moves when you turn the tuning dial) and 9 plates in the stator section (the part that does not move when turning the tuning dial).  

[Image: https://dl.dropboxusercontent.com/u/5462...0tuner.jpg]

Here is a link with instruction to add photographs to your posts if that would help you:
http://philcoradio.com/phorum/showthread.php?tid=29
#4

Hello Bob. thank you very much for your reply and especially forgive my bad English. He speaks from Spain. I am very happy to know that no missing sheet !! hehe. more sheets could have improved reception? You radio has boats round or square tune? I think our manufacturing radios may be a little earlier, could be ?? Thank you
#5

Same here.

Both rotor sections have 10 vanes and the stator sections have 9 plates.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#6

A delicate cleanup, maybe light brushing of De Oxit on the nasty area at the end? You may be able to avoid having to replace.

Paul 

Tubetalk1
#7

My 80 has round covers over the coils. See my thread at: http://philcoradio.com/phorum/showthread...0#pid45170

Paul, I think that's a "before" image on my tuner cap.
#8

I needa another cuppa Joe, thought it was radio in question!  Icon_redface

Maybe 2 cups.

Pablo

Tubetalk1
#9

Si, tenga dos tazas Icon_smile O una taza de espresso.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#10

(09-04-2016, 09:36 AM)klondike98 Wrote:  Mi 80 se cubre asalto sobre las bobinas. Ver mi hilo en: http://philcoradio.com/phorum/showthread...0#pid45170

Paul, creo que eso es un "antes" imagen en mi gorra sintonizador.

Bob, I've seen the pictures of your radio and is equal to mine (round cans), you have left the bright, how did you do it?? I have documented and carrying 11 sheets in the tuner, carrying the square cans. possibly our radios are older.
#11

(09-04-2016, 08:23 AM)Moti Wrote:  Hello Bob. thank you very much for your reply and especially forgive my bad English. He speaks from Spain. I am very happy to know that no missing sheet !! hehe. more sheets could have improved reception? You radio has boats round or square tune? I think our manufacturing radios may be a little earlier, could be ?? Thank you
Welcome Moti,

> more sheets could have improved reception?

Not so much what it would do is lower the frequency that you are receiving. If you removed sheets (plates) it would raise the frequency some what.

The shape of the coil shields is not all that important what is is whether or not the coils inside are good?? It's common for them to be bad (open windings). Repair is not very difficult if you have some small gauge magnet wire.

Bob mentioned these links on another thread for the model 80.

If you haven't seen them, there are several modifications suggested by Ron and posted on Chuck's website that can help the performance of the 80.


http://www.philcorepairbench.com/tips/svctip43.htm

http://www.philcorepairbench.com/tips/svctip44.htm

http://www.philcorepairbench.com/tips/svctip03.htm


GL
Terry

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#12

I think you are asking me, "how did the chassis become bright and shiney?"

My chassis had a lot of rust. I removed the rust with Naval Jelly. Then I painted the chassis with a Rustoleum paint, I think I used aluminum colored paint.
#13

Something about after my tuner and I feel like I am being mocked, which I deserve. 

Pablo

Tubetalk1
#14

thank you for your help. I'll start restoring these days. someone has made the modifications proposed in the above links ?? radio works best?
#15

Yes, those modifications have been done many times. They were recommended by Ron Ramirez, founder of this Phorum and well known for his expertise on Philco radios.




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
HiFi (Chifi) tube amp build - but my own design.
What may be lacking in the PP Tube amps may be the 2nd harmonics, which some, especially RCA back in the day called &quo...MrFixr55 — 05:32 PM
Jackson 715 not working
Usually in an emission tester, the tube under test is measured as if it were a diode. So, some testers connect all the g...RodB — 04:17 PM
Restoring Philco 37-604C
Yep. F5 is green, D5 is Red. Red is Bad. Green is Clean.morzh — 01:30 PM
Jackson 715 not working
I did start to do that but I stalled out because I could not figure out how the grid and plate get voltage. In this diag...daveone23 — 11:52 AM
Restoring Philco 37-604C
(Insert Homer Simpson "DOPF" Here.) When all fails, look at the can. Took the Ron Ramirez advice, red Caig D...MrFixr55 — 09:23 AM
Philco 91 Speaker Replacement
From your text I am not sure if you intend to use the existing speaker with a resistor instead of the field coil. It wo...morzh — 08:44 AM
Philco 91 Speaker Replacement
My field coil is bad. I am still hoping to find an original, but if I can't I will go with a fitting Philco speaker, 125...dconant — 08:34 AM
Philco 91 Speaker Replacement
As Rod said, it is OK to use a fitting speaker, and then look for an original one. If you buy a Hammond 125 output tr...morzh — 08:15 AM
Philco 91 Speaker Replacement
Yes, I often have to substitute, then keep an eye out for an original. In the meantime, the radio is working and being e...RodB — 08:02 AM
Philco 91 Speaker Replacement
I was wondering if I could use a more common Philco speaker and just add the resistance I need for the coil and get a ne...dconant — 07:45 AM

[-]
Who's Online
There are currently 2595 online users. [Complete List]
» 2 Member(s) | 2593 Guest(s)
AvatarAvatar

>