Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

1933-34 Philco 89B Restoration
#16

Jumping back into this Model 89. My workshop is filling up, and I need to start fixing and selling the sets I don't intend to keep. Label on the back of this one says it is a Code 121. My other 89 that I plan to keep is a Code 123. Icon_thumbup

I just went through my Cap stock and pulled everything.

Question: Bakelite Block 4989-W: The 200 ohm resistor: Is a 1 Watt replacement sufficient?

Blessings,
Jeff W.
Jonesboro, Arkansas

http://jeffsradios.weebly.com

God loves you as you are, not as you should be, because none of us are as we should be. - Brennan Manning
#17

I would just reinstall the original wire loop. It's better than any resistor you could put in there.

Steve

M R Radios   C M Tubes
#18

The plate current of the 39/44 tube (if the resistor is the one in the Cathode of it in parallel with the cap) is 6mA max, which will make the dissipated power 0.007 W (7mW), which means that any small resistor will do just fine.
If you could re-use the wire resistor that was there - great. Otherwise use any power you have.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#19

This might be a little after the fact but those cloth covered wire wound resistors don't take kindly to flexing or movement. Typically resistance wise they are very stable and should stay in tolerance. Just don't bend it.

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#20

Don't Breath on them,,,and no heat on ends,,,
#21

I wound up replacing the resistor in the bakelite block with a 1 watt I had on hand.  Icon_thumbup
This block and 1 other were done last night.
Electrolytics were replaced today.
I did a quick check of the transformer, some of the coils, and all the resistors.
All checked out, so I decided to turn it on, running it through my variac.

Here's a video I shot during the 1st power up test. All stations came in where they should on the dial.  Icon_thumbup

[Video: https://youtu.be/uxNjHNX4wvs]

Blessings,
Jeff W.
Jonesboro, Arkansas

http://jeffsradios.weebly.com

God loves you as you are, not as you should be, because none of us are as we should be. - Brennan Manning
#22

Last post, showed the radio up and running. I patched a couple pieces of missing wood in the upper part of the grill, did some touch-up work, and gave the cabinet a new coat of toner over the original, and a new grill cloth from Richmond Designs. It went to a new owner just before I left for my trip earlier in January. New owner is really happy, and I'm glad to start thinning out my workshop, and make a little money off the hobby. Here's some glamour shots before it went to its new home.

[Image: https://farm5.staticflickr.com/4578/2712...00f3_b.jpg]

Blessings,
Jeff W.
Jonesboro, Arkansas

http://jeffsradios.weebly.com

God loves you as you are, not as you should be, because none of us are as we should be. - Brennan Manning
#23

Looks very nice, Jeff!

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#24

Icon_thumbup Icon_thumbup Icon_thumbup




Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Jackson 715 not working
Mrfixr55, its working now. I cleaned the switches and sockets with spray cleaner. Thanks for helping on this one.daveone23 — 06:26 PM
Jackson 715 not working
Now that you posted the schematic, I don't know why that Sprague electrolytic cap is across the meter, as it is not indi...MrFixr55 — 05:51 PM
HiFi (Chifi) tube amp build - but my own design.
What may be lacking in the PP Tube amps may be the 2nd harmonics, which some, especially RCA back in the day called &quo...MrFixr55 — 05:32 PM
Jackson 715 not working
Usually in an emission tester, the tube under test is measured as if it were a diode. So, some testers connect all the g...RodB — 04:17 PM
Restoring Philco 37-604C
Yep. F5 is green, D5 is Red. Red is Bad. Green is Clean.morzh — 01:30 PM
Jackson 715 not working
I did start to do that but I stalled out because I could not figure out how the grid and plate get voltage. In this diag...daveone23 — 11:52 AM
Restoring Philco 37-604C
(Insert Homer Simpson "DOPF" Here.) When all fails, look at the can. Took the Ron Ramirez advice, red Caig D...MrFixr55 — 09:23 AM
Philco 91 Speaker Replacement
From your text I am not sure if you intend to use the existing speaker with a resistor instead of the field coil. It wo...morzh — 08:44 AM
Philco 91 Speaker Replacement
My field coil is bad. I am still hoping to find an original, but if I can't I will go with a fitting Philco speaker, 125...dconant — 08:34 AM
Philco 91 Speaker Replacement
As Rod said, it is OK to use a fitting speaker, and then look for an original one. If you buy a Hammond 125 output tr...morzh — 08:15 AM

[-]
Who's Online
There are currently no members online.

>