Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Another Philco Radio Question
#1

Guys I have to ask, I am able to purchase a Philco 37-650 console. I would love to hear everyones thoughts to weather it would be a radio to purchase or one to pass up on. The cabinet on the radio is in great shape. It is only missing one knob, the grill cloth is ok just a little stain on it. Let me know what you guys think, Thanks John
#2

They are pretty nice radios and perform very well. But, as with all 1937 Philcos, watch out for the infamous Unit Construction and the possibility of one or more coils being bad.

--
Ron Ramirez
Ferdinand IN
#3

Ron as you stated why do the coils end up being bad on the 1937 Philcos? Were they made badly or something?
#4

I understand that Philco used a sealing wax that had a high sulphur content and over the years/decades, moisture incursion along with the sulphur compounds creates weak sulphuric acid and that eats up copper very nicely. The "Greenies" is the blue-green copper sulphate leftover.

This is not an indictment of Philco. These sets were not expected to last 60-70 yrs after they left the factory.

Chuck
#5

The other theory I heard of was that some used a strip of celluloid plastic, with a high nitric acid content, and that damaged the coils, at least in the RF coils in the model 90s.
Regards
Arran
#6

That's what I haqve always heard about the Philco coils - the nitric acid in the celluloid damages the coils. It's usually the primaries (outer windings) that suffer the damage, but in advanced cases the inner (secondary) windings can also get the "greenies" as well.

Sulphur in the wax makes sense also. And a combination of these plus moisture equals trouble at some point for the coils.

As Chuck said, these radios were not intended to last 3/4 of a century or more. That many have is a testament to how well products were once made. To say more would mean going political, so let's leave it at that.

--
Ron Ramirez
Ferdinand IN




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Jackson 715 not working
Mrfixr55, its working now. I cleaned the switches and sockets with spray cleaner. Thanks for helping on this one.daveone23 — 06:26 PM
Jackson 715 not working
Now that you posted the schematic, I don't know why that Sprague electrolytic cap is across the meter, as it is not indi...MrFixr55 — 05:51 PM
HiFi (Chifi) tube amp build - but my own design.
What may be lacking in the PP Tube amps may be the 2nd harmonics, which some, especially RCA back in the day called &quo...MrFixr55 — 05:32 PM
Jackson 715 not working
Usually in an emission tester, the tube under test is measured as if it were a diode. So, some testers connect all the g...RodB — 04:17 PM
Restoring Philco 37-604C
Yep. F5 is green, D5 is Red. Red is Bad. Green is Clean.morzh — 01:30 PM
Jackson 715 not working
I did start to do that but I stalled out because I could not figure out how the grid and plate get voltage. In this diag...daveone23 — 11:52 AM
Restoring Philco 37-604C
(Insert Homer Simpson "DOPF" Here.) When all fails, look at the can. Took the Ron Ramirez advice, red Caig D...MrFixr55 — 09:23 AM
Philco 91 Speaker Replacement
From your text I am not sure if you intend to use the existing speaker with a resistor instead of the field coil. It wo...morzh — 08:44 AM
Philco 91 Speaker Replacement
My field coil is bad. I am still hoping to find an original, but if I can't I will go with a fitting Philco speaker, 125...dconant — 08:34 AM
Philco 91 Speaker Replacement
As Rod said, it is OK to use a fitting speaker, and then look for an original one. If you buy a Hammond 125 output tr...morzh — 08:15 AM

[-]
Who's Online
There are currently no members online.

>