Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco model #?
#1

Local radio but cant find model #

http://longisland.craigslist.org/atq/4415689836.html

Times I have been electrocuted in 2021
As of 1/01/2021
AC: 4 DC: 1
Last year: 6
#2

42-390x perhaps?

http://www.philcoradio.com/gallery/1942a.htm#v
#3

Thats her I think.
thanks eX

Does anyone know how good of a performer this radio is?

Times I have been electrocuted in 2021
As of 1/01/2021
AC: 4 DC: 1
Last year: 6
#4

Nothing terribly special except that it has the old FM band.
#5

I'd think the 42-390 would be a decent performer. I have a 42-355 with the same chassis. I pick up all kinds of distant stations on AM and SW even in my basement with just the built-in loop. The chassis is a devil to restore, though, because it has lots of crumbling rubber-insulated wire. There is also an enormous assembly combining the band switch, push-buttons, and power switch that is hard to re-wire.

The old FM band is useless, of course, though I can often pick up a strong local country station, probably from a harmonic in the converter stage. I didn't bother to align the FM on mine.

Restoration isn't really worse than any of the similar Philcos of the era with rubber wires, but it takes patience. It was actually one of the first few radios I restored. It took me a long time, but it didn't require any special skill or experience. If the band switch assembly is damaged or worn out, I don't know what you'd do.

John Honeycutt




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
RCA WV-98c
If this is R22, check the voltage on the wiper (86V). If this is R33, see if the lower pin indeed connected to GND, the ...morzh — 02:29 PM
Philco 38-2 Low Volume
Both sch, the one you showed in the beginning and the one I see on Nostalgia, show 40K for the 2nd audio plate.morzh — 02:25 PM
Model 96 cabinet veneer
I can't figure out what the first step is, let alone the final step. I have tried copying pictures from my hard drive a...TGLager — 01:40 PM
Philco 38-2 Low Volume
I managed to get some more time on this. Hi Mr. FixIT, The radio has been recapped. Many of the resistors were rep...dconant — 01:39 PM
Philco 38-2 Low Volume
Thanks guys for the help. I started looking at these points but I have to quit for the day. I will be looking into this ...dconant — 12:23 PM
RCA WV-98c
Check out this crazy zero pot operation. Touching it drives it crazy. Its rubber tipped. Also the 6al5 has no negative v...daveone23 — 12:08 PM
Philco 38-2 Low Volume
If you check all of that and still have a problem (my first inkling would be one of the 6F6s) then look at the 6J5 phase...RodB — 10:44 AM
RCA WV-98c
Those will probably depend on teh switch combination. Could you list some that you see, their values and what they sh...morzh — 10:26 AM
Model 96 cabinet veneer
You are probably skipping the final step. Once you select the photos you want and they get downloaded, the system assign...RodB — 09:36 AM
RCA WV-98c
At this point, there is no input, just internal voltages Which are incorrect and not sure what they should be.daveone23 — 09:15 AM

[-]
Who's Online
There are currently 1428 online users. [Complete List]
» 3 Member(s) | 1425 Guest(s)
AvatarAvatarAvatar

>