Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Finally Completed!
#1

The electronics were not too bad (except that super stuck band switch). Even the Bakelite blocks went fairly easy. The cabinet was more of a challenge. I ended up replacing the veneer on both sides and the top. The grill cloth is new also. I think it came out pretty good. By the way, It sounds great and picks up a lot of short wave, too Icon_clap  

       

Eric
The Villages, FL
Member: Philco Phorum, ARF, ARCI & Radiomuseum.org

#2

Came out great, Eric.
#3

Thanks, Morzh! At least I learned how to free up a frozen band switch.

Eric
The Villages, FL
Member: Philco Phorum, ARF, ARCI & Radiomuseum.org

#4

Very nice Icon_thumbup
#5

yeah....the word switch rhymes well with you know what for a reason, huh? Icon_lol
#6

nice job it came out quite nice.
#7

Great job! Icon_clap Icon_thumbup Icon_clap Icon_thumbup

Steve

M R Radios   C M Tubes
#8

Great job you did there Eric  Icon_smile
I recently got a 66B myself and I must say the cabinet style is quite the looker in my opinion.
#9

Super lookin' job!!
Icon_clap Icon_clap Icon_clap
#10

Eric,

Beautiful job!!!

What did you have to do to the band switch to get it moving? I've not had a frozen one yet, but I hear it happens, so it would help to have an idea how to deal with it.
#11

Really good job. Where did you get the large pieces of veneer?
#12

PAradiogeek: If you read this thread: http://philcoradio.com/phorum/showthread...110&page=2  It will give you an idea of how to free up the band switch.

Mike: I got the veneer here: Rockler I used the pressure sensitive type. It is really easy to work with.

Everyone else: Thanks for your comments. It  means a lot when I hear it from my friends on the Phorum Icon_thumbup

Eric
The Villages, FL
Member: Philco Phorum, ARF, ARCI & Radiomuseum.org





Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Jackson 715 not working
Mrfixr55, its working now. I cleaned the switches and sockets with spray cleaner. Thanks for helping on this one.daveone23 — 06:26 PM
Jackson 715 not working
Now that you posted the schematic, I don't know why that Sprague electrolytic cap is across the meter, as it is not indi...MrFixr55 — 05:51 PM
HiFi (Chifi) tube amp build - but my own design.
What may be lacking in the PP Tube amps may be the 2nd harmonics, which some, especially RCA back in the day called &quo...MrFixr55 — 05:32 PM
Jackson 715 not working
Usually in an emission tester, the tube under test is measured as if it were a diode. So, some testers connect all the g...RodB — 04:17 PM
Restoring Philco 37-604C
Yep. F5 is green, D5 is Red. Red is Bad. Green is Clean.morzh — 01:30 PM
Jackson 715 not working
I did start to do that but I stalled out because I could not figure out how the grid and plate get voltage. In this diag...daveone23 — 11:52 AM
Restoring Philco 37-604C
(Insert Homer Simpson "DOPF" Here.) When all fails, look at the can. Took the Ron Ramirez advice, red Caig D...MrFixr55 — 09:23 AM
Philco 91 Speaker Replacement
From your text I am not sure if you intend to use the existing speaker with a resistor instead of the field coil. It wo...morzh — 08:44 AM
Philco 91 Speaker Replacement
My field coil is bad. I am still hoping to find an original, but if I can't I will go with a fitting Philco speaker, 125...dconant — 08:34 AM
Philco 91 Speaker Replacement
As Rod said, it is OK to use a fitting speaker, and then look for an original one. If you buy a Hammond 125 output tr...morzh — 08:15 AM

[-]
Who's Online
There are currently 3953 online users. [Complete List]
» 1 Member(s) | 3952 Guest(s)
Avatar

>