Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Zenith TO Knob Bright Removal
#1

Does anybody know of a non-destructive way to remove the knob brights from Zenith TO knobs. I have a pair for an H500 that are a pretty corroded and I would like to polish them. I think polishing them would be a whole lot easier if I removed them.

My only idea, and I don't like it, is to drill a small hole through the knob from behind until I hit the bright. Then I could try pushing it off of the knob from behind.

It doesn't seem like there is any space around the edges to allow me to pry them off.

Can't think of anything witty.
Greg O.
Whitehall, PA
#2

Welcome to the Phorum!
Icon_wave

I do not think those brights come off easily.
#3

Hi Greg and welcome,
Your up there by Bob, Klondike and he seems to have an affinity for Zenith sets too. I'm down by Philly. Removing the brights from the knobs w/o damage is going to be difficult at best as they are pretty thin. A better solution may be to just rip them out and replace w/a new one. Check your local hardware store for replacement knobs with brights for various things like light dimmers and such. Most likely you'll find something a bit larger remove and cut it down to size and fit.

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#4

If you are willing to risk (BTW, why?) - Try heat, see if they come off.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#5

(11-11-2016, 08:27 AM)morzh Wrote:  If you are willing to risk (BTW, why?) - Try heat, see if they come off.

The knobs melt too easily. I am surprised by this one. Most of the brass falls off of the ones I have found and often has been lost. They may not be on there all that good - but good luck.

"I just might turn into smoke, but I feel fine"
http://www.russoldradios.com/
#6

(11-11-2016, 02:37 PM)Phlogiston Wrote:  
(11-11-2016, 08:27 AM)morzh Wrote:  If you are willing to risk (BTW, why?) - Try heat, see if they come off.

The knobs melt too easily. I am surprised by this one. Most of the brass falls off of the ones I have found and often has been lost. They may not be on there all that good - but good luck.

Hi Guys
You also may find that the corrosion is bad enough that you can't make them look good anyway. If those where made now days they have some sort of gold tone plastic piece. I wonder if there is a gold tone plastic tape??

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#7

Greg, what model TO do you have?  I have two knobs from an 8G005 that are not too bad and which you would be welcome to, but I think from the description you have a model with solid brights in the center of the knob.  

[Image: https://dl.dropboxusercontent.com/u/5462...005_35.jpg]
#8

Now that the chassis' done I've gotten around to the cabinet.

I haven't decided how to remove the brights yet, but I did try buffing one on the knob. Do you know that if you buff it enough brass turns to silver  Icon_eek -- oops! They're so small, I figured they'd be solid brass.

I'll either get some plating compound and fix the originals or take the coward's way out and use the spare, bright-less knobs I have with the repro brights I got from Antique Electronic Supply a while back. They don't seem to carry them any more.

Can't think of anything witty.
Greg O.
Whitehall, PA
#9

 Maybe you could try the opposite of heat with the knob brights, freeze them instead and the glue might give out.
Regards
Arran
#10

just go over top of them,,,,,GLUE ????
#11

I thought about trying to freeze them. If it was cheaper I would buy some of the wart remover spray and freeze try freezing the brights in the hope they would shrink enough to crack the glue beneath them.

The other thing I thought of was to glue something to the tops of them and try to pull them off. However I think that could end badly. I don't know what would stick and if it did how I'd get it off...

Maybe if I wait 65 more years they'll fall off on their own.

Can't think of anything witty.
Greg O.
Whitehall, PA




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 39-116 radio and remote
The transformer I located is from a Philco TV chassis, circa 1948. The part number is 32-8391 I do have the replace...Brad Winder — 08:59 PM
Philco 41-221 Restored
Hello Rod, Wow that radio looks great nice job ! Sincerely Richardradiorich — 07:39 PM
Philco 269 - 444 FIVE VALVE VERSION?
From what I can remember the model 444 "People's Radio" used a special tube/valve called a PenDD61, it was the...Arran — 06:54 PM
Philco 41-221 Restored
Nice Radioslford310 — 06:24 PM
Philco 269 - 444 FIVE VALVE VERSION?
Hi Chaz,  You may want to post the tubes used in your radio.   From Radio Museum, it seems that the set uses some ...MrFixr55 — 05:14 PM
Philco 41-221 Restored
Today my grandson and I finished the restoration of this Philco 41-221. It has had all the rubber coated wiring replaced...RodB — 03:19 PM
Philco 39-116 radio and remote
Hi Brad, I had no idea that the overheating was problematic in this radio.  Do you know the part number of the transfor...RichG — 03:01 PM
Philco 269 - 444 FIVE VALVE VERSION?
From the photo it looks the sockets are screwed and the front one does not even match the hole.morzh — 02:54 PM
Philco 269 - 444 FIVE VALVE VERSION?
Hi Chas a welcome, Perhaps we'll have to reverse engineer this to sort it. So let's start w/what tubes does it use? And...Radioroslyn — 12:28 PM
Philco 39-116 radio and remote
Hi Rich, From my experience, unfortunately it is not uncommon to find the power transformer in the 39-116 to be overhea...Brad Winder — 09:25 AM

[-]
Who's Online
There are currently no members online.

>