03-13-2013, 08:19 PM
Well, I've made a little more progress. Time has been a precious commodity lately and I haven't spent as much time at the workbench as I would like.
There's been a lot of veneer damage to this cabinet over the years. It was hard to find a spot on the side where the veneer wasn't split or coming off of the radio. So there's been a lot of this:
[Image: http://i243.photobucket.com/albums/ff93/...7c3d61.jpg]
And this:
[Image: http://i243.photobucket.com/albums/ff93/...3a2627.jpg]
And this:
[Image: http://i243.photobucket.com/albums/ff93/...207784.jpg]
The cabinet was actually pulling apart at the bottom. I was able to pull it almost all the way back together. After the glue sets up a little creative filling will hide most of the problem.
[Image: http://i243.photobucket.com/albums/ff93/...7f5f32.jpg]
So while the cabinet was all clamped up with no where to go I decided to turn my attention to the chassis. Its dirty and much of the wiring will need to be replaced. I'll also have to get up close and personal with a lot of Brasso. At least it's all there!
[Image: http://i243.photobucket.com/albums/ff93/...25fe9b.jpg]
Dirty dirty:
[Image: http://i243.photobucket.com/albums/ff93/...6bab5b.jpg]
Old wiring. Can't wait to get started on that!
[Image: http://i243.photobucket.com/albums/ff93/...d05409.jpg]
I started off by removing the tuning condenser. It was super dirty and greasy. It was partially covered in a grease that resembled axle grease in consistency. I wiped it down as much as I could:
[Image: http://i243.photobucket.com/albums/ff93/...28dae2.jpg]
I dunked it in the ultrasonic cleaner with some lukewarm water and dish washing detergent and ran it 4 times at 8 minutes. It came out much cleaner, but not perfect. The heavy grease was not going to be defeated so easily, but that didn't shock me. I'll pick up some Purple Power and let it soak for a bit. Still, I'm pretty happy with the ultrasonic cleaner, it got in between all of the plates really well:
[Image: http://i243.photobucket.com/albums/ff93/...737a4a.jpg]
That's it for now. Not a lot pf progress, but much of it is the slow process of clamp and wait, clamp and wait. My next post should show some significant progress on the chassis.
There's been a lot of veneer damage to this cabinet over the years. It was hard to find a spot on the side where the veneer wasn't split or coming off of the radio. So there's been a lot of this:
[Image: http://i243.photobucket.com/albums/ff93/...7c3d61.jpg]
And this:
[Image: http://i243.photobucket.com/albums/ff93/...3a2627.jpg]
And this:
[Image: http://i243.photobucket.com/albums/ff93/...207784.jpg]
The cabinet was actually pulling apart at the bottom. I was able to pull it almost all the way back together. After the glue sets up a little creative filling will hide most of the problem.
[Image: http://i243.photobucket.com/albums/ff93/...7f5f32.jpg]
So while the cabinet was all clamped up with no where to go I decided to turn my attention to the chassis. Its dirty and much of the wiring will need to be replaced. I'll also have to get up close and personal with a lot of Brasso. At least it's all there!
[Image: http://i243.photobucket.com/albums/ff93/...25fe9b.jpg]
Dirty dirty:
[Image: http://i243.photobucket.com/albums/ff93/...6bab5b.jpg]
Old wiring. Can't wait to get started on that!
[Image: http://i243.photobucket.com/albums/ff93/...d05409.jpg]
I started off by removing the tuning condenser. It was super dirty and greasy. It was partially covered in a grease that resembled axle grease in consistency. I wiped it down as much as I could:
[Image: http://i243.photobucket.com/albums/ff93/...28dae2.jpg]
I dunked it in the ultrasonic cleaner with some lukewarm water and dish washing detergent and ran it 4 times at 8 minutes. It came out much cleaner, but not perfect. The heavy grease was not going to be defeated so easily, but that didn't shock me. I'll pick up some Purple Power and let it soak for a bit. Still, I'm pretty happy with the ultrasonic cleaner, it got in between all of the plates really well:
[Image: http://i243.photobucket.com/albums/ff93/...737a4a.jpg]
That's it for now. Not a lot pf progress, but much of it is the slow process of clamp and wait, clamp and wait. My next post should show some significant progress on the chassis.
