Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco 116x speaker
#1

Where can I send my 116x speaker for repair, it needs a new voice coil and a new cone.
#2

I just went through this with an old H model. I still haven't ruled out doing it myself, but there is a guy in Ohio, one in New Jersey, one in Utah, and one in Georgia in addition to several smaller shops with no web presence. This forum has a list in the resources section, but the cost will be somewhere between $50-$90 depending on who does the work. Add to that the cost of shipping the speaker both ways.

http://www.philcoradio.com/resourceb.htm

Charlie in San Antonio
#3

There's Alabama radio society also.
#4

I think there is one in Michigan somewhere, and one in Oregon. The one in Oregon that I am thinking of does a lot of car radio speakers too, which are oval shaped, and they were reasonably priced compared to some of the others. When you look at what the cones and spiders actually cost, if you can find them, it makes many of the rates charged by some shops look like a ripoff. But you really have to go by reputation, some shops won't even touch a vintage speaker, claiming that can't get parts, which is partially true, but the real reason is that they would rather recone someone's JBLs for $150-175 a pop with off the shelf parts at a tremendous markup. I say partially true since a generic cone can be made to fit an old basket with minimal effort, it's only the voice coil and spider that could be a problem and require them to make something, which many either don't know how or don't care to do.
I myself would recone speakers if I could find the parts, I think that the 116X uses a 10'' so at least you can find those easily enough, mind you all bets are off if the voice coil is wrecked. At least these use a center mounted spider of the 45 RPM adapter style, you can make those yourself if you can't salvage the original.
Regards
Arran
#5

There is a place called Freeman Tuell speaker service in Dallas tx, they do excellent work on speaker reconing. I use them when I need that done on my antique radio speakers. Very reasonable prices . Call them at 214 324 1132
#6

Thanks to everyone for all the information .




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco model 38 code 121 not receiving signal.
So one last question before I finish this radio. Regarding the speaker and output transformer. I salvaged the original o...Stormlord5500 — 09:31 AM
462ron
It’s on the bottom of the homepage of our Philcoradio.com homepage! Ron462ron — 07:20 AM
Model 70 Cabinet Trim
Steve might have some trim left. Not sure he is making anything.morzh — 06:12 AM
Model 70 Cabinet Trim
Hello musar, First all welcome to the forum and yes that is true that steve stopped making trim . Sincerely Richar...radiorich — 12:13 AM
Model 70 Cabinet Trim
I have recently come into possession of a Model 70.  The trim around the base needs to be replaced.  If this were years ...musar — 12:07 AM
philcorepairbench.com - shadow-meter
Anyone know of a way to recover these files from the repair bench? Thanks. fenbach — 11:16 PM
Philco model 38 code 121 not receiving signal.
That's true. Of course If I were to get a vtvm I'd probably have to sink money in to it to get it working right. Probabl...Stormlord5500 — 08:44 PM
Philco model 38 code 121 not receiving signal.
A DMM is good enough. One rarely has to measure indictance, but if you do, short of getting a serious LCR meter (I hav...morzh — 07:35 PM
Testing a speaker and output transformer Trutone A2-G
You guy's are right on. I found a broken wire on the speaker plug that I replaced and all is well now. Have better volu...murf — 03:43 PM
Philco model 38 code 121 not receiving signal.
I need to get a vtvm. I think that little component tester is just more accurate. Plus it shows the inductance which is ...Stormlord5500 — 03:07 PM

[-]
Who's Online
There are currently no members online.

>