Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

15x dial needed
#1

New to this so please pardon my stupidity. Have a 15x for 30 years sitting around and finally decided to make a few repairs. the string is broke on the dial but more important is the "plastic"dial scale. been on all afternoon to find the scale and no luck. also need to refinish but that may wait till warmer weather. radio plays last time I plugged in to play but it appears there should be some replacements done on capacitors for safety?? I am old cutlass guy so this is not in my wheel house yet. thanks for any help. Oh, and need one left nob!
#2

Welcome to the Phorum. Some of the more experienced folks will have experience with this specific model but if it has never been recapped you do need to do that to avoid damaging the transformer or other parts of the radio. The electrolytic caps and paper caps (which in this radio are probably inside of bakelite blocks....see: http://www.philcoradio.com/tech/blocks.htm ) need replacing. A schematic can be found here: http://www.philcoradio.com/tech/images/15.jpg : additional info beyond the schematic here: http://www.philcorepairbench.com/schematics.htm . Some useful info if you've never worked on a radio is here: http://www.antiqueradio.org/begin.htm .

Try the folks on this list for the knob: http://www.philcoradio.com/resourceb.htm#l

Lots of threads on this Phorum about refinishing the radio correctly as well, just do a little searching around and asking questions.
#3

thanks for that info. lots of study to do. will tackle when satisfied. lots of caps in there




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
philco predicta
The model is the holiday without UHF It has no sound and I don't have an oscilloscope or signal generator.cgl18 — 08:51 PM
Philco model 38 code 121 not receiving signal.
I will definitely check my lead length and wire dressing. Thanks for the ideas.Stormlord5500 — 08:06 PM
Philco model 38 code 121 not receiving signal.
Do make sure that you twist the 3 wires from the chassis to the transformer, and dress away from tubes, especially audio...MrFixr55 — 07:38 PM
Philco model 38 code 121 not receiving signal.
The cone unfortunately got damaged when I removed it. The glue that held the cone to the basket was sloppily applied and...Stormlord5500 — 07:12 PM
Philco model 38 code 121 not receiving signal.
So what was wrong with the original speaker? Was the cone damaged? Unless it's totally hopeless I would put it aside as ...Arran — 05:31 PM
My collection presentation
There is an article on my site that introduces the first portable radios in my collection. I have only provided a link t...Vlad95 — 01:17 PM
Electrolytic restuffing/internals
Bridkarl This specific cap you have is the easiset type to restuff. I usually cut it at the upper border of the depr...morzh — 11:35 AM
philco predicta
Hi CGL18, First off, welcome to the Philco Phorum. I have not worked on a TV for a while but here are some givens: ...MrFixr55 — 08:22 AM
Another amp build - here I go again!
Sweet! I actually have a Dynaco Mark 4 that I had been running with 6L6s with no mods. Seemed to my 14-year-old head a...MrFixr55 — 12:57 AM
PT-6 finished!!
Hi Gang, Tube heaters are not "Ohmic" devices (that maintain specified resistance over wide temperature, c...MrFixr55 — 12:03 AM

[-]
Who's Online
There are currently 1107 online users. [Complete List]
» 1 Member(s) | 1106 Guest(s)
Avatar

>