Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 1 Vote(s) - 4 Average
  • 1
  • 2
  • 3
  • 4
  • 5

*Solved Minerva Tropic Master model w117 "early"-crackle pop & no vol ****SOLVED

I believe springy material on brake lines is to reduce vibration, lessens chance of a rub through. Older vehicles like my '69 Cobra Jet didn't use them, but my '72 Comet does have wrap on lines.

Tom

wiper to ground reads about 7 ohms this time, sometimes its 10, others is 2 and other times its like 20 but still low enough.

so... the ref gnd signal is stable enough to not be the fault for this.

it could be several things.

i tried calibrating down in resistivity of the 47kohm R after the wiper,, still have sound with vol at Min.

i think i will just live with it.

this bugger gets really HOT on the outside,,

headed out to put it back inside its carry case after i add my antenna relay back on.
i am considering a 120 v small fan to mount inside it....

new cooling fan in,,, now that really took care of the heat.


air intake is in the "back door"
air hits ceiling and goes left and right out the side louvers.


Attached Files Image(s)
       

i really want to add a couple things to this set

i want an S meter

i want a BFO even if its a gimick type.
i am getting a lot of side band in addtion to shortwave

i am going to start with the gimmick BFO type for side band if anyone has suggestions.

i know i will need another tuning cap which i have several.

from there i will need a knob on the tuning cap which i have.

i can string up and make a 0-100 scale which will be visible in the lower part of the main tuning window just below the words printed "tropic master".

how do i wire in such a thing?
do i attempt to copy cat the gimmick from my hallicrafters S38-d which actually works really great!.

any ideas or anyone experienced in doing this?

Hello friends, I loved seeing all the work in this rarity of 1944, I have a radio of this model here and I need to restore it, it is not as beautiful as this one on the topic, what was written in most components has worn out over time, I need to replace components mainly capacitors, I don't have his technical documentation, if any of your friends know of a site that I can download, please let me know, thank you very much !.

W-117 early version:

http://www.nostalgiaair.org/pagesbymodel...010877.pdf

W-117 late version:

http://www.nostalgiaair.org/pagesbymodel...010878.pdf

Better copies can be found here:

https://worldradiohistory.com/Archive-Ri...45-MNO.pdf

Good luck!

John KK4ZLF
Lexington, KY
"illegitimis non carborundum"




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco model 38 code 121 not receiving signal.
So one last question before I finish this radio. Regarding the speaker and output transformer. I salvaged the original o...Stormlord5500 — 09:31 AM
462ron
It’s on the bottom of the homepage of our Philcoradio.com homepage! Ron462ron — 07:20 AM
Model 70 Cabinet Trim
Steve might have some trim left. Not sure he is making anything.morzh — 06:12 AM
Model 70 Cabinet Trim
Hello musar, First all welcome to the forum and yes that is true that steve stopped making trim . Sincerely Richar...radiorich — 12:13 AM
Model 70 Cabinet Trim
I have recently come into possession of a Model 70.  The trim around the base needs to be replaced.  If this were years ...musar — 12:07 AM
philcorepairbench.com - shadow-meter
Anyone know of a way to recover these files from the repair bench? Thanks. fenbach — 11:16 PM
Philco model 38 code 121 not receiving signal.
That's true. Of course If I were to get a vtvm I'd probably have to sink money in to it to get it working right. Probabl...Stormlord5500 — 08:44 PM
Philco model 38 code 121 not receiving signal.
A DMM is good enough. One rarely has to measure indictance, but if you do, short of getting a serious LCR meter (I hav...morzh — 07:35 PM
Testing a speaker and output transformer Trutone A2-G
You guy's are right on. I found a broken wire on the speaker plug that I replaced and all is well now. Have better volu...murf — 03:43 PM
Philco model 38 code 121 not receiving signal.
I need to get a vtvm. I think that little component tester is just more accurate. Plus it shows the inductance which is ...Stormlord5500 — 03:07 PM

[-]
Who's Online
There are currently 1727 online users. [Complete List]
» 2 Member(s) | 1725 Guest(s)
AvatarAvatar

>