Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco 42-345 grille cloth and knob decals
#1

Hi guys. I was wondering if a person can get exact replacement grille cloth and decals knobs for a Philo 42-345. Thanks! Brian
#2

Welcome to the Phorum!!
Check RadioDaze for decals.  The knobs on that one are a little unusual so try the folks that Ron has listed as resources for knobs.  David, Julie, Kelton and Mike supply original knobs.  I've bought from all but Kelton in the past.  You may have to try them all as they don't have every knob for every radio. The grill cloth looks a bit like the whiskey rayon that Kenneth Richmonds sells but its a little hard to see in the 42-345 photos I was looking at.  
#3

no no no whiskey rayon!


It is like carpeting and I used one off ebay that matched pretty good.


Attached Files Image(s)
   

Times I have been electrocuted in 2021
As of 1/01/2021
AC: 4 DC: 1
Last year: 6
#4

Hi. I know this is an old thread, but I have the same radio and looking for grill cloth. Can you tell me where you found that one or a name for it?
#5

Welcome MamaJennie! Nichael Katz has a site called Radio Grill Cloth. Good source for fabric.
https://www.radiogrillecloth.com/
Try Radio Daze for knob decals.
https://www.radiodaze.com/decals-48/
Hope this helps. Gary

"Don't pity the dead, pity the living, above all, those living without love."
Professor Albus Dumbledore
Gary - Westland Michigan
#6

I’ve recently used both Michael Katz’s fabric and Radio Daze’s decals for a radio of my own. I can attest that you’ll be most satisfied.

My only advice, when ordering the decals, is to make sure that your decal kit includes the “Philco” decal. The kit I ordered had all other decals but not this one, so I needed to order a separate Philco decal. I noticed that other decal kits do include the branding, so just be mindful!

Joseph

Philco 46-480
Philco 49-906
#7

Another learning experience I had. You will benefit tremendously from purchasing decal softener and setting solutions such as Micro-Sol and Micro-Set, AK Interactive Decal Setting Solution, or the like. This will really help to conform the new decals to the surface of your radio and will eliminate the laminated look of your decals.

Joseph

Philco 46-480
Philco 49-906
#8

Thank you. Where would I find those products?
#9

Right now Mike is probably the only good source of Philco-specific cloth, as well as others (I bought both Philco and RCA from him).

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#10

Hello MamaJennie. Just click on the highlighted web addresses in post number 5. Gary

"Don't pity the dead, pity the living, above all, those living without love."
Professor Albus Dumbledore
Gary - Westland Michigan




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 42-345 Restoration/Repair
The thrill is gone again, thought I was close to being done with it. Well Friday it was receiving broadcast, Saturday mo...osanders0311 — 07:47 PM
Help with Supreme 599
Iam getting closer to fixing it. I bumped Up the tranny voltage to get 5v on the 80 tube. I gan get the needle to move ...daveone23 — 03:41 PM
Philco 42-345 Restoration/Repair
Hello RodB, Checking my previous post I realized you're the one with the 42-340. I replaced the string for the tuning...osanders0311 — 03:12 PM
5U4 vs 5Z4 tubes
I saw no evidence of anything going wrong. The transformer is fused already which is nice. Interestingly the 5z4 did...bridkarl — 02:37 PM
5U4 vs 5Z4 tubes
I doubt anything cooked in 30 seconds because of the oops! These are very similar tubes, and nothing but transformer re...GarySP — 02:30 PM
Restoration of the Canadian General Electric A-87
Paul Philco322.You will be keeping very busy, you may have to go back to work for a breakIcon_smile. Paul To rel...RadioSvit — 01:57 PM
5U4 vs 5Z4 tubes
I grabbed the wrong tube and put in a 5U4 tube instead of the 5Z4 - I just had the rectifier in with no other tubes. Af...bridkarl — 01:54 PM
Restoration of the Canadian General Electric A-87
After applying the filler to the entire body, I noticed that the shades of the facade and the side and top walls were ve...RadioSvit — 01:49 PM
Restoration of the Canadian General Electric A-87
You will be keeping very busy, you may have to go back to work for a break:). PaulPaul Philco322 — 01:46 PM
Restoration of the Canadian General Electric A-87
After removing the control knobs, chassis, dynamics and scale frame, I first started restoring the torn piece of veneer....RadioSvit — 01:20 PM

[-]
Who's Online
There are currently 823 online users. [Complete List]
» 1 Member(s) | 822 Guest(s)
Avatar

>