Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

RCA 110K2 Unexpected project
#91

The first coat of oil dried up, leaving dull patches where it had coated bare wood. On Wednesday morning I found time to pass gently over the right side of the cabinet with 0000 wire wool, and rub in another coat of tung oil. Looking again this morning, it appears this approach is working nicely, a deep color and good finish is beginning to develop.

I have refinished a number of pieces of furniture this way, including our "Danish Modern" coffee table. This had been very neglected before we got to it, but (a lot of) TLC returned it to glory.

I don't hold with furniture that talks.
#92

OK, here are a couple of hasty garage shots of the cabinet after a little more refinishing attention today. Coming along nicely, I think:

   

   

I don't hold with furniture that talks.
#93

Nice Job! I have a 110k console sitting waiting for the chassic to come back to me. A friend is going through it. I do not have the know how of replacing the caps and such. My radio cabinet looks nothing like brand new but its good enough. Hope they both work great when done.  Icon_thumbup
#94

More picture later. I declared satisfaction with the cabinet, and refitted the chassis, grillecloth, speaker etc.

Done!

I don't hold with furniture that talks.
#95

And here she is:

I went downstairs this morning to take a picture, and discovered two things. One, the preset buttons were acting lazy, calling for a little lubrication. Second, a casual glance revealed the dial glass was in backwards! All corrected now, and it plays nicely:


   

I don't hold with furniture that talks.
#96

Looks great Ed  Icon_thumbup

Did you mention that you used Tung oil to touch up the finish?

John KK4ZLF
Lexington, KY
"illegitimis non carborundum"
#97

Thanks Elliot

Yes, Tung oil. It seems to work best applied quite sparingly in several sessions. Allow a few days in between rub-downs. I don't know if it works with grain filling products, but I have applied it over fillers (furniture repair and refinishing) with good results.

Cheers,

Ed

I don't hold with furniture that talks.




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Jackson 715 not working
Now that you posted the schematic, I don't know why that Sprague electrolytic cap is across the meter, as it is not indi...MrFixr55 — 05:51 PM
HiFi (Chifi) tube amp build - but my own design.
What may be lacking in the PP Tube amps may be the 2nd harmonics, which some, especially RCA back in the day called &quo...MrFixr55 — 05:32 PM
Jackson 715 not working
Usually in an emission tester, the tube under test is measured as if it were a diode. So, some testers connect all the g...RodB — 04:17 PM
Restoring Philco 37-604C
Yep. F5 is green, D5 is Red. Red is Bad. Green is Clean.morzh — 01:30 PM
Jackson 715 not working
I did start to do that but I stalled out because I could not figure out how the grid and plate get voltage. In this diag...daveone23 — 11:52 AM
Restoring Philco 37-604C
(Insert Homer Simpson "DOPF" Here.) When all fails, look at the can. Took the Ron Ramirez advice, red Caig D...MrFixr55 — 09:23 AM
Philco 91 Speaker Replacement
From your text I am not sure if you intend to use the existing speaker with a resistor instead of the field coil. It wo...morzh — 08:44 AM
Philco 91 Speaker Replacement
My field coil is bad. I am still hoping to find an original, but if I can't I will go with a fitting Philco speaker, 125...dconant — 08:34 AM
Philco 91 Speaker Replacement
As Rod said, it is OK to use a fitting speaker, and then look for an original one. If you buy a Hammond 125 output tr...morzh — 08:15 AM
Philco 91 Speaker Replacement
Yes, I often have to substitute, then keep an eye out for an original. In the meantime, the radio is working and being e...RodB — 08:02 AM

[-]
Who's Online
There are currently no members online.

>